MPC564MZP56 Freescale Semiconductor, MPC564MZP56 Datasheet - Page 949

• Manufacturer Part Number: MPC564MZP56
• Description: IC MCU 512K FLASH 56MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Core: PowerPC
• Processor Series: MPC5xx
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 56 MHz
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 56
• Number Of Timers: 2
• Operating Supply Voltage: 0 V to 5 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 32
• Height: 1.95 mm
• Interface Type: CAN, JTAG, QSPI, SCI, SPI, UART
• Length: 27 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 2.7 V, 5.25 V
• Supply Voltage (min): 2.5 V, 4.75 V
• Width: 27 mm
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

When not in debug mode the sequencing error encoding indicates that the transmission from the external
development tool was a debug mode transmission. When a sequencing error occurs the development port
will ignore the data shifted in while the sequencing error was shifting out. It will be treated as a NOP
function.
Finally, the null output encoding is used to indicate that the previous transmission did not have any
associated errors.
When not in debug mode, ready will be asserted at the end of each transmission. If debug mode is not
enabled and transmission errors can be guaranteed not to occur, the status output is not needed.
23.4.6.8
When in debug mode the development port starts communications by setting DSDO low to indicate that
the CPU is trying to read an instruction from DPIR or data from DPDR. When the CPU writes data to the
port to be shifted out the ready bit is not set. The port waits for the CPU to read the next instruction before
asserting ready. This allows duplex operation of the serial port while allowing the port to control all
transmissions from the external development tool. After detecting this ready status the external
development tool begins the transmission to the development port with a start bit (logic high) on the DSDI
pin.
23.4.6.9
mode/status bit, a control/status bit, and 32 bits of data. All instructions and data for the CPU are
transmitted with the mode bit cleared indicating a 32-bit data field. The encoding of data shifted into the
development port shift register (through the DSDI pin) is shown below in
Freescale Semiconductor
In debug mode the 35 bits of the development port shift register are interpreted as a start/ready bit, a
1
2
Ready
The “Freeze” status is set to (1) when the CPU is in debug mode and to (0) otherwise.
The “Download Procedure in progress” status is asserted (0) when Debug port in the Download procedure and is
negated (1) otherwise.
(0)
(0)
(0)
(0)
Development Port Serial Communications — Debug Mode
Serial Data Into Development Port
Table 23-12. Status / Data Shifted Out of Development Port Shift Register
0
0
1
1
Status [0:1]
0
1
0
1
MPC561/MPC563 Reference Manual, Rev. 1.2
Freeze
status
Bit 0
1
Procedure
Download
progress
Bit 1
in
2
Data
Data
(Depending on Input Mode)
Bits 2:31 or 2:6 —
1’s
1’s
1’s
Table
23-13.
Valid Data from CPU
Sequencing Error
CPU Interrupt
Null
Function
Development Support
23-35