UPD70F3771GF-GAT-AX Renesas Electronics America, UPD70F3771GF-GAT-AX Datasheet - Page 445

• Manufacturer Part Number: UPD70F3771GF-GAT-AX
• Description: MCU 32BIT V850ES/JX3-H 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Hr

Specifications of UPD70F3771GF-GAT-AX

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 48MHz
• Connectivity: CAN, CSI, EBI/EMI, I²C, UART/USART, USB
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 2.85 V ~ 3.6 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

V850ES/JG3-H, V850ES/JH3-H
R01UH0042EJ0400 Rev.4.00
Sep 30, 2010
TT0IOC0
After reset: 00H
Note The output level of the timer output pins (TOT00 and TOT01) specified by the
Cautions 1. If the setting of the TT0IOC0 register is changed when TOT00 and
TT0OL1
TT0OE1
TT0OL0
TT0OE0
TOT0n pin output
• When TT0OLn bit = 0
0
1
0
1
0
1
0
1
7
0
16-bit counter
TT0OLn bit is shown below (n = 0, 1).
TT0CE bit
R/W
Timer output prohibited
• Low level is output from the TOT01 pin when the TT0OL1 bit = 0.
• High level is output from the TOT01 pin when the TT0OL1 bit = 1.
Timer output enabled (A pulse is output from the TOT01 pin.)
Timer output prohibited
• Low level is output from the TOT00 pin when the TT0OL0 bit = 0.
• High level is output from the TOT00 pin when the TT0OL0 bit = 1.
Timer output enabled (A pulse is output from the TOT00 pin.)
2. Rewrite the TT0OL1, TT0OE1, TT0OL0, and TT0OE0 bits when the
3. Even if the TT0OL0 or TT0OL1 bit is manipulated when the TT0CE,
TOT01 pin starts output at high level.
TOT01 pin starts output at low level.
TOT00 pin starts output at high level.
TOT00 pin starts output at low level.
6
0
TOT01 outputs are set for the port mode, the output of the pins
change. Set the port in the input mode and make the port go into a
high-impedance state, noting changes in the pin status.
TT0CTL0.TT0CE bit = 0. (The same value can be written when the
TT0CE bit = 1.)
TT0CE bit to 0 and then set the bits again.
TT0OE0, and TT0OE1 bits are 0, the output level of the TOT00 and
TOT01 pins changes.
Address: FFFFF603H
5
0
CHAPTER 9 16-BIT TIMER/EVENT COUNTER T (TMT)
TOT01 pin output level setting
TOT00 pin output level setting
TOT01 pin output setting
TOT00 pin output setting
4
0
If rewriting was mistakenly performed, clear the
TOT0n pin output
• When TT0OLn bit = 1
TT0OL1 TT0OE1
16-bit counter
3
TT0CE bit
<2>
Note
Note
TT0OL0
1
TT0OE0
<0>
Page 445 of 1509