DF61654N50FTV Renesas Electronics America, DF61654N50FTV Datasheet - Page 641

• Manufacturer Part Number: DF61654N50FTV
• Description: IC H8SX/1654 MCU FLASH 120TQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8SX/1600r

Specifications of DF61654N50FTV

• Core Processor: H8SX
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, IrDA, SCI, SmartCard, USB
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 75
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: External
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 120-TQFP, 120-VQFP
• For Use With: HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)3DK1657 - DEV EVAL KIT FOR H8SX/1657
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

14.4.5
Figure 14.9 shows an example of the operation for transmission in asynchronous mode. In
transmission, the SCI operates as described below.
1. The SCI monitors the TDRE flag in SSR, and if it is cleared to 0, recognizes that data has been
2. After transferring data from TDR to TSR, the SCI sets the TDRE flag to 1 and starts
3. Data is sent from the TxD pin in the following order: start bit, transmit data, parity bit or
4. The SCI checks the TDRE flag at the timing for sending the stop bit.
5. If the TDRE flag is 0, the next transmit data is transferred from TDR to TSR, the stop bit is
6. If the TDRE flag is 1, the TEND flag in SSR is set to 1, the stop bit is sent, and then the mark
Figure 14.10 shows a sample flowchart for transmission in asynchronous mode.
written to TDR, and transfers the data from TDR to TSR.
transmission. If the TIE bit in SCR is set to 1 at this time, a TXI interrupt request is generated.
Because the TXI interrupt processing routine writes the next transmit data to TDR before
transmission of the current transmit data has finished, continuous transmission can be enabled.
multiprocessor bit (may be omitted depending on the format), and stop bit.
sent, and then serial transmission of the next frame is started.
state is entered in which 1 is output. If the TEIE bit in SCR is set to 1 at this time, a TEI
interrupt request is generated.
TXI interrupt
request generated
TDRE
TEND
Figure 14.9 Example of Operation for Transmission in Asynchronous Mode
Serial Data Transmission (Asynchronous Mode)
1
Start
bit
0
Data written to TDR and
TDRE flag cleared to 0 in
TXI interrupt processing
routine
D0
(Example with 8-Bit Data, Parity, One Stop Bit)
D1
1 frame
Data
D7
Parity
bit
0/1
TXI interrupt
request generated
Section 14 Serial Communication Interface (SCI, IrDA, CRC)
Stop
bit
1
Start
bit
0
D0
D1
Rev.1.00 Sep. 08, 2005 Page 591 of 966
Data
D7
Parity
bit
TEI interrupt
request generated
0/1
Stop
bit
1
REJ09B0219-0100
Idle state
(mark state)
1