DF2218BR24V Renesas Electronics America, DF2218BR24V Datasheet - Page 587

• Manufacturer Part Number: DF2218BR24V
• Description: IC H8S/2218 MCU FLASH 112-LFBGA
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2200r

Specifications of DF2218BR24V

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: SCI, SmartCard, USB
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 6x10b
• Oscillator Type: External
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 112-LFBGA
• For Use With: HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)3DK2218-SS - KIT DEV H8S/2218 WINDOWS SIDESHW3DK2218 - DEV EVAL KIT H8S/2218
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Note: * Interrupts should be masked from when the IRQ6 interrupt is received until the SLEEP instruction is executed.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
Guide to Flowchart Figures
Unmask all interrupts with LDC instruction, etc.*
Finally, unmask the interrupts using the LDC instruction or the like and execute the SLEEP instruction immediately
afterward.
Mask all interrupts with LDC instruction, etc.*
Procedure to enter power-down mode
Specify IRQ6 to falling edge sensitive
Set SPRSi and SPRSs in UIFR3 to 1
(Stop MSTPB0 in MSTPCRB to 1)
All USB module internal clocks stop
IRQ6 = Low (falling edge output)
(Write IRQ6SCB and IRQ6SCA
Detect USB bus suspend state
Enter USB module stop 2 state
Confirm SPRSs in UIFR3 as 1
(Execute SLEEP instruction)
Clear SPRSi in UIFR3 to 0
Enter power-down mode*
Clear IRQ6E in IER to 0 *
All LSI internal clocks stop
: Indicates operations to be done
: Indicates operations to be
(Set IRQ6E in IER to 1)
Set IRQ6E in IER to 1*
Set IRQ6F in ISR to 1
by firmware.
automatically done by hardware
in this LSI.
USPND pin = High
in ISCRH to 01
IRQ6 = High
Figure 14.28 Flowchart
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
Rev.7.00 Dec. 24, 2008 Page 531 of 698
Procedure to cancel power-down mode
restarted by using various USB registers
USB communication operations can be
Wait for system clock stabilization time
(Wait for CK48READY in UIFR3 is set to 1)
(For crystal oscillator clock: 4 ms min.)
USB module intenal clock operation starts
(LSI internal clock starts oscillation)
(Clear MSTPB0 in MSTPCRB to 0)
(For external clok: 16 states min.)
Wait 2 ms for USB operation clock
IRQ6 = Low (falling edge output)
Cancel USB module stop2 mode
(USB operating clock stabilized)
Set CK48READY in UIFR3 to 1
Clear SPRSs of UIFR3 to 0
Clear SPRSi in UIFR3 to 0
Cancel power-down mode
Set SPRSi of UIFR3 to 1
Detect USB bus resume
Set SOF of UIFR3 to 1
Set IRQ6F in ISR to 1
Detect SOF packet
USPND pin = Low
Enter active mode
IRQ6 = High
to stabilize
REJ09B0074-0700