HD64F2638F20J Renesas Electronics America, HD64F2638F20J Datasheet - Page 1017

• Manufacturer Part Number: HD64F2638F20J
• Description: IC H8S MCU FLASH 256K 128-QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2600r

Specifications of HD64F2638F20J

• Core Processor: H8S/2600
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, SCI, SmartCard
• Peripherals: Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 72
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 128-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

H8S/2639, H8S/2638, H8S/2636,
H8S/2630, H8S/2635 Group
23B.6.2 Clearing Software Standby Mode
Software standby mode is cleared by an external interrupt (NMI pin, or pins IRQ0 to IRQ5), or by
means of the RES pin or STBY pin.
• Clearing with an interrupt
• Clearing with the RES pin
• Clearing with the STBY pin
23B.6.3 Setting Oscillation Stabilization Time after Clearing Software Standby Mode
Bits STS2 to STS0 in SBYCR should be set as described below.
Using a Crystal Oscillator:
1. Setting for H8S/2636, H8S/2638, H8S/2639, H8S/2630
REJ09B0103-0800 Rev. 8.00
May 28, 2010
When an NMI or IRQ0 to IRQ5 interrupt request signal is input, clock oscillation starts, and
after the elapse of the time set in bits STS2 to STS0 in SYSCR, stable clocks are supplied to
the entire chip, software standby mode is cleared, and interrupt exception handling is started.
When clearing software standby mode with an IRQ0 to IRQ5 interrupt, set the corresponding
enable bit to 1 and ensure that no interrupt with a higher priority than interrupts IRQ0 to IRQ5
is generated. Software standby mode cannot be cleared if the interrupt has been masked on the
CPU side or has been designated as a DTC activation source.
When the RES pin is driven Low, clock oscillation is started. At the same time as clock
oscillation starts, clocks are supplied to the entire chip. Note that the RES pin must be held
Low until clock oscillation stabilizes. When the RES pin goes high, the CPU begins reset
exception handling.
When the STBY pin is driven Low, a transition is made to hardware standby mode.
Set bits STS2 to STS0 so that the standby time is at least 8 ms (the oscillation stabilization
time).
Table 23B-6 shows the standby times for different operating frequencies and settings of bits
STS2 to STS0.
HD64F2630UF, HD6432630UF, HD64F2630WF, HD6432630WF, HD6432635F, HD64F2635F, HD6432634F]
Section 23B Power-Down Modes [HD64F2636UF, HD6432636UF, HD64F2638UF, HD6432638UF,
HD64F2638WF, HD6432638WF, HD64F2639UF, HD6432639UF, HD64F2639WF, HD6432639WF,
Page 967 of 1458