SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 187

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

12.1.2
ARM DDI0198D
Static power management (leakage control)
EDBGRQ
nIRQ
nFIQ
When the ARM926EJ-S has entered a low-power state, all of the main internal clocks
are stopped, including the clock for the ARM9EJ-S core. However, the ARM9EJ-S is
active if DBGTCKEN is asserted. This enables values to be written in the ARM9EJ-S
debug control register so that a debugger can force an exit from wait for interrupt mode.
This means that you can safely stop the ARM926EJ-S CLK if STANDBYWFI is
HIGH and DBGTCKEN is LOW.
Figure 12-2 shows the recommended logic for stopping the main ARM926EJ-S clock
during wait for interrupt.
The nature of the nFIQ, nIRQ, and EDBGRQ signals enables them to be registered
prior to being used in the gating logic. DBGTCKEN must be used combinationally to
maintain the relationship between the ARM926EJ-S JTAG logic and the RTCK signal
used by the debugger. See the ARM9EJ-S Technical Reference Manual for details of
how DBGTCKEN is generated and used.
The ARM926EJ-S design is partitioned so that the SRAM blocks that are used for the
caches and the MMU can be powered down under certain conditions.
Cache RAMs
The RAMs for either of the caches can be safely powered down if the respective cache
has been disabled (using CP15 control register c1) and it contains no valid entries.
While a cache is disabled, only explicit CP15 operations can cause the cache RAMs to
be accessed (c7 cache maintenance operations). These instructions must not be
executed while any of the cache RAMs are powered down. If any of the RAMs for a
cache have been powered down, then they must be powered up prior to re-enabling the
relevant cache.
Copyright © 2001-2003 ARM Limited. All rights reserved.
Figure 12-2 Logic for stopping ARM926EJ-S clock during wait for interrupt
FCLK = Free running clock
CLK = Clock supplied to ARM926EJ-S macrocell
FCLK
DBGTCKEN
STANDBYWFI
FCLK
HRESETn
RST
EN
Power Management
CLK
12-3