HD6432670 Hitachi, HD6432670 Datasheet - Page 163
HD6432670
Manufacturer Part Number
HD6432670
Description
(HD64F267x Series) 16-Bit Microcomputer
Manufacturer
Hitachi
Datasheet
1.HD6432670.pdf
(953 pages)
- Current page: 163 of 953
- Download datasheet (6Mb)
5.7.2
Instructions that disable interrupts are LDC, ANDC, ORC, and XORC. After any of these
instructions is executed, all interrupts including NMI are disabled and the next instruction is
always executed. When the I bit is set by one of these instructions, the new value becomes valid
two states after execution of the instruction ends.
5.7.3
There are times when interrupt acceptance is disabled by the interrupt controller.
The interrupt controller disables interrupt acceptance for a 3-state period after the CPU has
updated the mask level with an LDC, ANDC, ORC, or XORC instruction.
5.7.4
Interrupt operation differs between the EEPMOV.B instruction and the EEPMOV.W instruction.
With the EEPMOV.B instruction, an interrupt request (including NMI) issued during the transfer
is not accepted until the transfer is completed.
With the EEPMOV.W instruction, if an interrupt request is issued during the transfer, interrupt
exception handling starts at a break in the transfer cycle. The PC value saved on the stack in this
case is the address of the next instruction. Therefore, if an interrupt is generated during execution
of an EEPMOV.W instruction, the following coding should be used.
5.7.5
When the ITSR setting is changed, an edge occurs internally and the IRQnF bit (n = 0 to 15) of
ISR may be set to 1 at the unintended timing if the selected pin level before the change is different
from the selected pin level after the change. If the IRQn interrupt request (n = 0 to 15) is enabled,
the interrupt exception handling is executed. To prevent the unintended interrupt, ITSR setting
should be changed while the IRQn interrupt request is disabled, then the IRQnF bit should be
cleared to 0.
L1:
Instructions that Disable Interrupts
Times when Interrupts are Disabled
Interrupts during Execution of EEPMOV Instruction
Change of IRQ Pin Select Register (ITSR) Setting
EEPMOV.W
MOV.W
BNE
R4,R4
L1
Rev. 2.0, 04/02, page 117 of 906
Related parts for HD6432670
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Silicon N-Channel Power MOS FET Module
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
High Speed Power Switching
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
Silicon N-Channel IGBT
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
8MHz V(cc): -0.3 to +7.0V V(in): -0.3 to +0.3V advanced CRT controller (ACRTC)
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-word ? 4-bit High Speed CMOS Static RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
SINGLE CHIP CODEC WITH FILTERS(COMBO)
Manufacturer:
HITACHI
Datasheet: