HD6432670 Hitachi, HD6432670 Datasheet - Page 718
HD6432670
Manufacturer Part Number
HD6432670
Description
(HD64F267x Series) 16-Bit Microcomputer
Manufacturer
Hitachi
Datasheet
1.HD6432670.pdf
(953 pages)
- Current page: 718 of 953
- Download datasheet (6Mb)
15.5
Multiprocessor Communication Function
Use of the multiprocessor communication function enables data transfer to be performed among a
number of processors sharing communication lines by means of asynchronous serial
communication using the multiprocessor format, in which a multiprocessor bit is added to the
transfer data. When multiprocessor communication is carried out, each receiving station is
addressed by a unique ID code. The serial communication cycle consists of two component
cycles: an ID transmission cycle which specifies the receiving station, and a data transmission
cycle to the specified receiving station. The multiprocessor bit is used to differentiate between the
ID transmission cycle and the data transmission cycle. If the multiprocessor bit is 1, the cycle is
an ID transmission cycle, and if the multiprocessor bit is 0, the cycle is a data transmission cycle.
Figure 15.10 shows an example of inter-processor communication using the multiprocessor
format. The transmitting station first sends communication data with a 1 multiprocessor bit added
to the ID code of the receiving station. It then sends transmit data as data with a 0 multiprocessor
bit added. When data with a 1 multiprocessor bit is received, the receiving station compares that
data with its own ID. The station whose ID matches then receives the data sent next. Stations
whose ID does not match continue to skip data until data with a 1 multiprocessor bit is again
received.
The SCI uses the MPIE bit in SCR to implement this function. When the MPIE bit is set to 1,
transfer of receive data from RSR to RDR, error flag detection, and setting the SSR status flags,
RDRF, FER, and ORER to 1 are inhibited until data with a 1 multiprocessor bit is received. On
reception of receive character with a 1 multiprocessor bit, the MPBR bit in SSR is set to 1 and the
MPIE bit is automatically cleared, thus normal reception is resumed. If the RIE bit in SCR is set to
1 at this time, an RXI interrupt is generated.
When the multiprocessor format is selected, the parity bit setting is invalid. All other bit settings
are the same as those in normal asynchronous mode. The clock used for multiprocessor
communication is the same as that in normal asynchronous mode.
Rev. 2.0, 04/02, page 672 of 906
Related parts for HD6432670
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Silicon N-Channel Power MOS FET Module
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
High Speed Power Switching
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
Silicon N-Channel IGBT
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
8MHz V(cc): -0.3 to +7.0V V(in): -0.3 to +0.3V advanced CRT controller (ACRTC)
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-word ? 4-bit High Speed CMOS Static RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
SINGLE CHIP CODEC WITH FILTERS(COMBO)
Manufacturer:
HITACHI
Datasheet: