PIC18F27J53T-I/SO Microchip Technology, PIC18F27J53T-I/SO Datasheet - Page 206

• Manufacturer Part Number: PIC18F27J53T-I/SO
• Description: 28-pin, USB, 128KB Flash, 4KB RAM, 12 MIPS, 12-bit ADC, NanoWatt XLP 28 SOIC .30
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J53T-I/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.8 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F47J53 FAMILY
12.1
Timer0 can operate as either a timer or a counter. The
mode is selected with the T0CS bit (T0CON<5>). In
Timer mode (T0CS = 0), the module increments on
every clock by default unless a different prescaler value
is selected (see Section 12.3 “Prescaler”). If the
TMR0 register is written to, the increment is inhibited
for the following two instruction cycles. The user can
work around this by writing an adjusted value to the
TMR0 register.
The Counter mode is selected by setting the T0CS bit
(= 1). In this mode, Timer0 increments either on every
rising edge or falling edge of the pin, T0CKI. The
incrementing edge is determined by the Timer0 Source
Edge Select bit, T0SE (T0CON<4>); clearing this bit
selects the rising edge. Restrictions on the external
clock input are discussed below.
An external clock source can be used to drive Timer0;
however, it must meet certain requirements to ensure
that the external clock can be synchronized with the
FIGURE 12-1:
FIGURE 12-2:
DS39964B-page 206
Note: Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI max. prescale.
T0CKI pin
Note: Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI max. prescale.
T0CKI pin
Timer0 Operation
T0SE
T0CS
T0PS<2:0>
PSA
F
OSC
T0SE
T0CS
T0PS<2:0>
PSA
/4
F
OSC
TIMER0 BLOCK DIAGRAM (8-BIT MODE)
TIMER0 BLOCK DIAGRAM (16-BIT MODE)
/4
0
1
0
1
Programmable
Prescaler
Programmable
3
Prescaler
3
1
0
Preliminary
1
0
(2 T
Sync with
Internal
Clocks
CY
(2 T
Delay)
Sync with
Internal
Clocks
CY
internal phase clock (T
synchronization and the onset of incrementing the
timer/counter.
12.2
TMR0H is not the actual high byte of Timer0 in 16-bit
mode. It is actually a buffered version of the real high
byte of Timer0, which is not directly readable nor
writable (refer to Figure 12-2). TMR0H is updated with
the contents of the high byte of Timer0 during a read of
TMR0L. This provides the ability to read all 16 bits of
Timer0 without having to verify that the read of the high
and low byte were valid, due to a rollover between
successive reads of the high and low byte.
Similarly, a write to the high byte of Timer0 must also
take place through the TMR0H Buffer register. The high
byte is updated with the contents of TMR0H when a
write occurs to TMR0L. This allows all 16 bits of Timer0
to be updated at once.
Delay)
Timer0 Reads and Writes in
16-Bit Mode
TMR0L
8
8
TMR0L
8
8
OSC
 2010 Microchip Technology Inc.
High Byte
TMR0H
TMR0
8
). There is a delay between
8
Set
TMR0IF
on Overflow
Internal Data Bus
8
Set
TMR0IF
on Overflow
Read TMR0L
Write TMR0L
Internal Data Bus