PIC18F27J53T-I/SO Microchip Technology, PIC18F27J53T-I/SO Datasheet - Page 278

• Manufacturer Part Number: PIC18F27J53T-I/SO
• Description: 28-pin, USB, 128KB Flash, 4KB RAM, 12 MIPS, 12-bit ADC, NanoWatt XLP 28 SOIC .30
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J53T-I/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.8 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F47J53 FAMILY
19.4.1
In Half-Bridge mode, two pins are used as outputs to
drive push-pull loads. The PWM output signal is output
on the PxA pin, while the complementary PWM output
signal is output on the PxB pin (see Figure 19-6). This
mode can be used for half-bridge applications, as
shown in Figure 19-7, or for full-bridge applications,
where four power switches are being modulated with
two PWM signals.
In Half-Bridge mode, the programmable dead-band delay
can be used to prevent shoot-through current in
half-bridge power devices. The value of the PxDC<6:0>
bits of the ECCPxDEL register sets the number of
instruction cycles before the output is driven active. If the
value is greater than the duty cycle, the corresponding
output remains inactive during the entire cycle. For more
details on the dead-band delay operations, see
Section 19.4.6 “Programmable Dead-Band Delay
Mode”.
FIGURE 19-7:
DS39964B-page 278
Standard Half-Bridge Circuit (“Push-Pull”)
Half-Bridge Output Driving a Full-Bridge Circuit
HALF-BRIDGE MODE
EXAMPLE OF HALF-BRIDGE APPLICATIONS
PxA
PxB
PxA
PxB
Preliminary
FET
Driver
FET
Driver
FET
Driver
FET
Driver
Since the PxA and PxB outputs are multiplexed with the
port data latches, the associated TRIS bits must be
cleared to configure PxA and PxB as outputs.
FIGURE 19-6:
PxA
PxB
td = Dead-Band Delay
Note 1: At this time, the TMR2 register is equal to the
(2)
(2)
2: Output signals are shown as active-high.
(1)
Load
V+
td
PR2 register.
Pulse Width
Period
Load
td
EXAMPLE OF
HALF-BRIDGE PWM
OUTPUT
 2010 Microchip Technology Inc.
FET
Driver
FET
Driver
(1)
+
-
+
-
Period
(1)