PIC18F27J53T-I/SO Microchip Technology, PIC18F27J53T-I/SO Datasheet - Page 357

• Manufacturer Part Number: PIC18F27J53T-I/SO
• Description: 28-pin, USB, 128KB Flash, 4KB RAM, 12 MIPS, 12-bit ADC, NanoWatt XLP 28 SOIC .30
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J53T-I/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.8 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

21.2.2
The receiver block diagram is displayed in Figure 21-6.
The data is received on the RXx pin and drives the data
recovery block. The data recovery block is actually a
high-speed shifter, operating at x16 times the baud
rate, whereas the main receive serial shifter operates
at the bit rate or at F
used in RS-232 systems.
To set up an Asynchronous Reception:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. If using interrupts, ensure that the GIE and PEIE
FIGURE 21-6:
 2010 Microchip Technology Inc.
Initialize the SPBRGHx:SPBRGx registers for
the appropriate baud rate. Set or clear the
BRGH and BRG16 bits, as required, to achieve
the desired baud rate.
Enable the asynchronous serial port by clearing
bit, SYNC, and setting bit, SPEN.
If interrupts are desired, set enable bit, RCxIE.
If 9-bit reception is desired, set bit, RX9.
Enable the reception by setting bit, CREN.
Flag bit, RCxIF, will be set when reception is
complete and an interrupt will be generated if
enable bit, RCxIE, was set.
Read the RCSTAx register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREGx register.
If any error occurred, clear the error by clearing
enable bit, CREN.
bits in the INTCON register (INTCON<7:6>) are
set.
EUSART ASYNCHRONOUS
RECEIVER
RXx
BRG16
OSC
EUSARTx RECEIVE BLOCK DIAGRAM
SPBRGHx
. This mode would typically be
Baud Rate Generator
x64 Baud Rate CLK
and Control
Pin Buffer
SPEN
SPBRGx
Recovery
Interrupt
Preliminary
 64
 16
 4
Data
or
or
CREN
PIC18F47J53 FAMILY
21.2.3
This mode would typically be used in RS-485 systems.
To set up an Asynchronous Reception with Address
Detect Enable:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. If any error occurred, clear the CREN bit.
11. If the device has been addressed, clear the
RX9
Initialize the SPBRGHx:SPBRGx registers for
the appropriate baud rate. Set or clear the
BRGH and BRG16 bits, as required, to achieve
the desired baud rate.
Enable the asynchronous serial port by clearing
the SYNC bit and setting the SPEN bit.
If interrupts are required, set the RCEN bit and
select the desired priority level with the RCxIP bit.
Set the RX9 bit to enable 9-bit reception.
Set the ADDEN bit to enable address detect.
Enable reception by setting the CREN bit.
The RCxIF bit will be set when reception is
complete. The interrupt will be Acknowledged if
the RCxIE and GIE bits are set.
Read the RCSTAx register to determine if any
error occurred during reception, as well as read
bit 9 of data (if applicable).
Read RCREGx to determine if the device is
being addressed.
ADDEN bit to allow all received data into the
receive buffer and interrupt the CPU.
Stop
MSb
RCxIF
RCxIE
RX9D
SETTING UP 9-BIT MODE WITH
ADDRESS DETECT
(8)
OERR
7
RSR Register
RCREGx Register

8
Data Bus
1
FERR
0
DS39964B-page 357
LSb
Start
FIFO