PIC18F27J53T-I/SO Microchip Technology, PIC18F27J53T-I/SO Datasheet - Page 427

• Manufacturer Part Number: PIC18F27J53T-I/SO
• Description: 28-pin, USB, 128KB Flash, 4KB RAM, 12 MIPS, 12-bit ADC, NanoWatt XLP 28 SOIC .30
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J53T-I/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.8 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

27.1.5
The CTMU sets its interrupt flag (PIR3<2>) whenever
the current source is enabled, then disabled. An inter-
rupt is generated only if the corresponding interrupt
enable bit (PIE3<2>) is also set. If edge sequencing is
not enabled (i.e., Edge 1 must occur before Edge 2), it
is necessary to monitor the edge status bits and
determine which edge occurred last and caused the
interrupt.
27.2
The following sequence is a general guideline used to
initialize the CTMU module:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Clear the Edge Status bits: EDG2STAT and
11. Enable both edge inputs by setting the EDGEN
 2010 Microchip Technology Inc.
Select the current source range using the IRNG
bits (CTMUICON<1:0>).
Adjust the current source trim using the ITRIM
bits (CTMUICON<7:2>).
Configure the edge input sources for Edge 1 and
Edge 2 by setting the EDG1SEL and EDG2SEL
bits (CTMUCONL<3:2> and <6:5>).
Configure the input polarities for the edge inputs
using the EDG1POL and EDG2POL bits
(CTMUCONL<7,4>). The default configuration
is for negative edge polarity (high-to-low
transitions).
Enable edge sequencing using the EDGSEQEN
bit
sequencing is disabled.
Select the operating mode (Measurement or
Time Delay) with the TGEN bit. The default
mode is Time/Capacitance Measurement.
Discharge the connected circuit by setting the
IDISSEN bit (CTMUCONH<1>). After waiting a
sufficient time for the circuit to discharge, clear
IDISSEN.
Disable the module by clearing the CTMUEN bit
(CTMUCONH<7>).
Enable the module by setting the CTMUEN bit.
EDG1STAT (CTMUCONL<1:0>).
bit (CTMUCONH<3>).
CTMU Module Initialization
(CTMUCONH<2>).
INTERRUPTS
By
default,
edge
Preliminary
PIC18F47J53 FAMILY
Depending on the type of measurement or pulse
generation being performed, one or more additional
modules may also need to be initialized and configured
with the CTMU module:
• Edge Source Generation: In addition to the
• Capacitance or Time Measurement: The CTMU
• Pulse Generation: When generating system
27.3
The CTMU requires calibration for precise measure-
ments of capacitance and time, as well as for accurate
time delay. If the application only requires measurement
of a relative change in capacitance or time, calibration is
usually not necessary. An example of this type of appli-
cation would include a capacitive touch switch, in which
the touch circuit has a baseline capacitance, and the
added capacitance of the human body changes the
overall capacitance of a circuit.
If actual capacitance or time measurement is required,
two hardware calibrations must take place: the current
source needs calibration to set it to a precise current,
and the circuit being measured needs calibration to
measure and/or nullify all other capacitance other than
that to be measured.
27.3.1
The current source on board the CTMU module has a
range of ±60% nominal for each of three current
ranges. Therefore, for precise measurements, it is pos-
sible to measure and adjust this current source by
placing a high-precision resistor, R
analog channel. An example circuit is shown in
Figure 27-2. The current source measurement is
performed using the following steps:
1.
2.
3.
4.
5.
6.
external edge input pins, both Timer1 and the
Output Compare/PWM1 module can be used as
edge sources for the CTMU.
module uses the A/D Converter to measure the
voltage across a capacitor that is connected to one
of the analog input channels.
clock, independent output pulses, the CTMU
module uses Comparator 2 and the associated
comparator voltage reference.
Initialize the A/D Converter.
Initialize the CTMU.
Enable the current source by setting EDG1STAT
(CTMUCONL<0>).
Issue settling time delay.
Perform A/D conversion.
Calculate the present source current using
I = V/ R
resistance and V is measured by performing an
A/D conversion.
Calibrating the CTMU Module
CURRENT SOURCE CALIBRATION
CAL
, where R
CAL
is a high-precision
CAL
DS39964B-page 427
, onto an unused