PIC18F27J53T-I/SO Microchip Technology, PIC18F27J53T-I/SO Datasheet - Page 371

• Manufacturer Part Number: PIC18F27J53T-I/SO
• Description: 28-pin, USB, 128KB Flash, 4KB RAM, 12 MIPS, 12-bit ADC, NanoWatt XLP 28 SOIC .30
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J53T-I/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.8 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

The ANCON0 and ANCON1 registers are used to
configure the operation of the I/O pin associated with
each analog channel. Setting any one of the PCFG bits
configures the corresponding pin to operate as a digital
only I/O. Clearing a bit configures the pin to operate as
an analog input for either the A/D Converter or the
comparator module. All digital peripherals are disabled
and digital inputs read as ‘0’. As a rule, I/O pins that are
multiplexed with analog inputs default to analog
operation on device Resets.
In order to correctly perform A/D conversions on the V
band gap reference (ADCON0<5:2> = 1111), the refer-
ence circuit must be powered on first. The VBGEN bit in
the ANCON1 register allows the firmware to manually
REGISTER 22-4:
REGISTER 22-5:
 2010 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-0
Note 1:
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4-0
PCFG7
VBGEN
R/W-0
R/W-0
(1)
These bits are only available only on 44-pin devices.
PCFG<7:0>: Analog Port Configuration bits (AN7-AN0)
1 = Pin configured as a digital port
0 = Pin configured as an analog channel – digital input disabled and reads ‘0’
VBGEN: 1.2V Band Gap Reference Enable bit
1 = 1.2V band gap reference is powered on
0 = 1.2V band gap reference is turned off to save power (if no other modules are requesting it)
Reserved: Always maintain as ‘0’ for lowest power consumption
Unimplemented: Read as ‘0’
PCFG<12:8>: Analog Port Configuration bits (AN12-AN8)
1 = Pin configured as a digital port
0 = Pin configured as an analog channel – digital input disabled and reads ‘0’
PCFG6
R/W-0
R
r
ANCON0: A/D PORT CONFIGURATION REGISTER 0 (BANKED F48h)
ANCON1: A/D PORT CONFIGURATION REGISTER 1 (BANKED F49h)
(1)
W = Writable bit
r = Reserved bit
W = Writable bit
‘1’ = Bit is set
‘1’ = Bit is set
PCFG5
R/W-0
U-0
—
(1)
PCFG12
PCFG4
R/W-0
R/W-0
Preliminary
BG
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
PIC18F47J53 FAMILY
PCFG11
PCFG3
R/W-0
R/W-0
request that the band gap reference circuit should be
enabled. For best accuracy, firmware should allow a
settling time of at least 10 ms prior to performing the first
acquisition on this channel after enabling the band gap
reference.
The reference circuit may already have been turned on
if some other hardware module (such as the on-chip
voltage regulator, comparators or HLVD) has already
requested it. In this case, the initial turn-on settling time
may have already elapsed and firmware does not need
to wait as long before measuring V
sition is complete, firmware may clear the VBGEN bit,
which will save a small amount of power if no other
modules are still requesting the V
PCFG10
PCFG2
R/W-0
R/W-0
x = Bit is unknown
x = Bit is unknown
PCFG1
PCFG9
R/W-0
R/W-0
BG
BG
DS39964B-page 371
reference.
. Once the acqui-
PCFG0
PCFG8
R/W-0
R/W-0
bit 0
bit 0