DF2398TE20 Renesas Electronics America, DF2398TE20 Datasheet - Page 502

• Manufacturer Part Number: DF2398TE20
• Description: IC H8S MCU FLASH 256K 120TQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2300r

Specifications of DF2398TE20

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: SCI, SmartCard
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 87
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 120-TQFP, 120-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Other names: HD64F2398TE20; HD64F2398TE20

For details of the multiprocessor communication function, see section 14.3.3, Multiprocessor Communication Function.
Bits 1 and 0—Clock Select 1 and 0 (CKS1, CKS0): These bits select the clock source for the baud rate generator. The
clock source can be selected from ø, ø/4, ø/16, and ø/64, according to the setting of bits CKS1 and CKS0.
For the relation between the clock source, the bit rate register setting, and the baud rate, see section 14.2.8, Bit Rate
Register (BRR).
14.2.6
SCR is a register that performs enabling or disabling of SCI transfer operations, serial clock output in asynchronous mode,
and interrupt requests, and selection of the serial clock source.
SCR can be read or written to by the CPU at all times.
SCR is initialized to H'00 by a reset, and by putting the device in standby mode or module stop mode. In the H8S/2398,
H8S/2394, H8S/2392, and H8S/2390, however, the value in SCR is initialized to H'00 by a reset, or in hardware standby
mode, but SCR retains its current state when the device enters software standby mode or module stop mode.
Bit 7—Transmit Interrupt Enable (TIE): Enables or disables transmit data empty interrupt (TXI) request generation
when serial transmit data is transferred from TDR to TSR and the TDRE flag in SSR is set to 1.
Note:* TXI interrupt request cancellation can be performed by reading 1 from the TDRE flag, then clearing it to 0, or
Rev.6.00 Oct.28.2004 page 472 of 1016
REJ09B0138-0600H
Bit
Initial value :
R/W
clearing the TIE bit to 0.
Serial Control Register (SCR)
Bit 2
MP
0
1
Bit 1
CKS1
0
1
Bit 7
TIE
0
1
:
:
R/W
TIE
7
0
Description
Multiprocessor function disabled
Multiprocessor format selected
Bit 0
CKS0
0
1
0
1
Description
Transmit data empty interrupt (TXI) requests disabled*
Transmit data empty interrupt (TXI) requests enabled
R/W
RIE
6
0
Description
ø clock
ø/4 clock
ø/16 clock
ø/64 clock
R/W
TE
5
0
R/W
RE
4
0
MPIE
R/W
3
0
TEIE
R/W
2
0
CKE1
R/W
1
0
CKE0
R/W
0
0
(Initial value)
(Initial value)
(Initial value)