DF2398TE20 Renesas Electronics America, DF2398TE20 Datasheet - Page 612

• Manufacturer Part Number: DF2398TE20
• Description: IC H8S MCU FLASH 256K 120TQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2300r

Specifications of DF2398TE20

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: SCI, SmartCard
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 87
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 120-TQFP, 120-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Other names: HD64F2398TE20; HD64F2398TE20

19.7
19.7.1
Note: * Determined by the state of the FWE pin.
FLMCR1 is an 8-bit register used for flash memory operating mode control. Program-verify mode or erase-verify mode is
entered by setting SWE to 1 when FWE = 1. Program mode is entered by setting SWE to 1 when FWE = 1, then setting
the PSU bit in FLMCR2, and finally setting the P bit. Erase mode is entered by setting SWE to 1 when FWE = 1, then
setting the ESU bit in FLMCR2, and finally setting the E bit. FLMCR1 is initialized by a reset, and in hardware standby
mode and software standby mode. Its initial value is H'80 when a high level is input to the FWE pin, and H'00 when a low
level is input. When on-chip flash memory is disabled, a read will return H'00, and writes are invalid.
Writes to the SWE bit in FLMCR1 are enabled only when FWE = 1; writes to the EV and PV bits only when FWE=1 and
SWE=1; writes to the E bit only when FWE = 1, SWE = 1, and ESU = 1; and writes to the P bit only when FWE = 1,
SWE = 1, and PSU = 1.
Bit 7—Flash Write Enable Bit (FWE): Sets hardware protection against flash memory programming/erasing. See
section 19.14, Flash Memory Programming and Erasing Precautions, before using this bit.
Bit 6—Software Write Enable Bit (SWE): Enables or disables flash memory programming. SWE should be set before
setting bits ESU, PSU, EV, PV, E, P, and EB9 to EB0, and should not be cleared at the same time as these bits.
Bits 5 and 4—Reserved: These bits cannot be modified and are always read as 0.
Rev.6.00 Oct.28.2004 page 582 of 1016
REJ09B0138-0600H
Bit
Initial value
Read/Write
Register Descriptions
Flash Memory Control Register 1 (FLMCR1)
Bit 7
FWE
0
1
Bit 6
SWE
0
1
FWE
—*
7
R
Description
When a low level is input to the FWE pin (hardware-protected state)
When a high level is input to the FWE pin
Description
Writes disabled
Writes enabled
[Setting condition]
When FWE = 1
SWE
R/W
6
0
—
—
5
0
—
—
4
0
R/W
EV
3
0
R/W
PV
2
0
R/W
1
E
0
R/W
0
0
P
(Initial value)