MC9S12G FREESCALE [Freescale Semiconductor, Inc], MC9S12G Datasheet - Page 655

• Manufacturer Part Number: MC9S12G
• Description: Ignores external trigger. Performs one conversion sequence and stops.
• Manufacturer: FREESCALE [Freescale Semiconductor, Inc]

20.4.1
The prescaler divides the bus clock by 1, 2, 4, 8, 16, 32, 64 or 128. The prescaler select bits, PR[2:0], select
the prescaler divisor. PR[2:0] are in timer system control register 2 (TSCR2).
The prescaler divides the bus clock by a prescalar value. Prescaler select bits PR[2:0] of in timer system
control register 2 (TSCR2) are set to define a prescalar value that generates a divide by 1, 2, 4, 8, 16, 32,
64 and 128 when the PRNT bit in TSCR1 is disabled.
By enabling the PRNT bit of the TSCR1 register, the performance of the timer can be enhanced. In this
case, it is possible to set additional prescaler settings for the main timer counter in the present timer by
using PTPSR[7:0] bits of PTPSR register generating divide by 1, 2, 3, 4,....20, 21, 22, 23,......255, or 256.
20.4.2
Clearing the I/O (input/output) select bit, IOSx, configures channel x as an input capture channel. The
input capture function captures the time at which an external event occurs. When an active edge occurs on
the pin of an input capture channel, the timer transfers the value in the timer counter into the timer channel
registers, TCx.
The minimum pulse width for the input capture input is greater than two bus clocks.
An input capture on channel x sets the CxF flag. The CxI bit enables the CxF flag to generate interrupt
requests. Timer module or Pulse Accumulator must stay enabled (TEN bit of TSCR1 or PAEN bit of
PACTL register must be set to one) while clearing CxF (writing one to CxF).
20.4.3
Setting the I/O select bit, IOSx, configures channel x when available as an output compare channel. The
output compare function can generate a periodic pulse with a programmable polarity, duration, and
frequency. When the timer counter reaches the value in the channel registers of an output compare channel,
the timer can set, clear, or toggle the channel pin if the corresponding OCPDx bit is set to zero. An output
compare on channel x sets the CxF flag. The CxI bit enables the CxF flag to generate interrupt requests.
Timer module or Pulse Accumulator must stay enabled (TEN bit of TSCR1 or PAEN bit of PACTL register
must be set to one) while clearing CxF (writing one to CxF).
The output mode and level bits, OMx and OLx, select set, clear, toggle on output compare. Clearing both
OMx and OLx results in no output compare action on the output compare channel pin.
Setting a force output compare bit, FOCx, causes an output compare on channel x. A forced output
compare does not set the channel flag.
The following channel 7 feature is available only when channel 7 exists. A channel 7 event, which can be
a counter overflow when TTOV[7] is set or a successful output compare on channel 7, overrides output
compares on all other output compare channels. The output compare 7 mask register masks the bits in the
output compare 7 data register. The timer counter reset enable bit, TCRE, enables channel 7 output
compares to reset the timer counter. A channel 7 output compare can reset the timer counter even if the
IOC7 pin is being used as the pulse accumulator input.
Freescale Semiconductor
This document is valid for the S12G96 and the S12G128 device. All information related to other devices is preliminary.
Prescaler
Input Capture
Output Compare
MC9S12G Family Reference Manual, Rev.1.01
Timer Module (TIM16B8CV3)
655