MC9S08JM60CLH Freescale, MC9S08JM60CLH Datasheet - Page 175

• Manufacturer Part Number: MC9S08JM60CLH
• Manufacturer: Freescale

Specifications of MC9S08JM60CLH

• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 24MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 4KB
• # I/os (max): 51
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 12-chx12-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: LQFP
• Program Memory Type: Flash
• Program Memory Size: 60KB
• Lead Free Status / RoHS Status: Compliant

After a repeated start condition (Sr), all other slave devices also compare the first seven bits of the first
byte of the slave address with their own addresses and test the eighth (R/W) bit. However, none of them
are addressed because R/W = 1 (for 10-bit devices) or the 11110XX slave address (for 7-bit devices) does
not match.
After the master-receiver has sent the first byte of the 10-bit address, the slave-transmitter sees an IIC
interrupt. Software must ensure the contents of IICD are ignored and not treated as valid data for this
interrupt.
11.4.3
General calls can be requested in 7-bit address or 10-bit address. If the GCAEN bit is set, the IIC matches
the general call address as well as its own slave address. When the IIC responds to a general call, it acts as
a slave-receiver and the IAAS bit is set after the address cycle. Software must read the IICD register after
the first byte transfer to determine whether the address matches is its own slave address or a general call.
If the value is 00, the match is a general call. If the GCAEN bit is clear, the IIC ignores any data supplied
from a general call address by not issuing an acknowledgement.
11.5
The IIC is disabled after reset. The IIC cannot cause an MCU reset.
11.6
The IIC generates a single interrupt.
An interrupt from the IIC is generated when any of the events in
is set. The interrupt is driven by bit IICIF (of the IIC status register) and masked with bit IICIE (of the IIC
control register). The IICIF bit must be cleared by software by writing a 1 to it in the interrupt routine. You
can determine the interrupt type by reading the status register.
11.6.1
The TCF (transfer complete flag) bit is set at the falling edge of the ninth clock to indicate the completion
of byte transfer.
Freescale Semiconductor
S
11110 + AD10 + AD9
Slave Address
1st 7 bits
Resets
Interrupts
General Call Address
Byte Transfer Interrupt
Table 11-10. Master-Receiver Addresses a Slave-Transmitter with a 10-bit Address
Match of received calling address
R/W
0
Complete 1-byte transfer
A1
Interrupt Source
Arbitration Lost
Slave Address
2nd byte
AD[8:1]
MC9S08JM60 Series Data Sheet, Rev. 3
Table 11-11. Interrupt Summary
A2
Sr
11110 + AD10 + AD9
Slave Address
Status
ARBL
IAAS
TCF
1st 7 bits
Table 11-11
IICIF
IICIF
IICIF
Flag
R/W
1
Local Enable
A3
occur, provided the IICIE bit
IICIE
IICIE
IICIE
Data
A
...
Data
A
175
P