MC9S08JM60CLH Freescale, MC9S08JM60CLH Datasheet - Page 189

• Manufacturer Part Number: MC9S08JM60CLH
• Manufacturer: Freescale

Specifications of MC9S08JM60CLH

• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 24MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 4KB
• # I/os (max): 51
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 12-chx12-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: LQFP
• Program Memory Type: Flash
• Program Memory Size: 60KB
• Lead Free Status / RoHS Status: Compliant

12.3.4
Freescale Semiconductor
IREFST
CLKST
PLLST
LOCK
LOLS
Field
3:2
7
6
5
4
Reset:
POR:
W
R
MCG Status and Control Register (MCGSC)
Loss of Lock Status — This bit is a sticky indication of lock status for the FLL or PLL. LOLS is set when lock
detection is enabled and after acquiring lock, the FLL or PLL output frequency has fallen outside the lock exit
frequency tolerance, D
reset or by writing a logic 1 to LOLS when LOLS is set. Writing a logic 0 to LOLS has no effect.
0 FLL or PLL has not lost lock since LOLS was last cleared.
1 FLL or PLL has lost lock since LOLS was last cleared.
Lock Status — Indicates whether the FLL or PLL has acquired lock. Lock detection is disabled when both the
FLL and PLL are disabled. If the lock status bit is set then changing the value of any of the following bits IREFS,
PLLS, RDIV[2:0], TRIM[7:0] (if in FEI or FBI modes), or VDIV[3:0] (if in PBE or PEE modes), will cause the lock
status bit to clear and stay cleared until the FLL or PLL has reacquired lock. Stop mode entry will also cause the
lock status bit to clear and stay cleared until the FLL or PLL has reacquired lock. Entry into BLPI or BLPE mode
will also cause the lock status bit to clear and stay cleared until the MCG has exited these modes and the FLL or
PLL has reacquired lock.
0 FLL or PLL is currently unlocked.
1 FLL or PLL is currently locked.
PLL Select Status — The PLLST bit indicates the current source for the PLLS clock. The PLLST bit does not
update immediately after a write to the PLLS bit due to internal synchronization between clock domains.
0 Source of PLLS clock is FLL clock.
1 Source of PLLS clock is PLL clock.
Internal Reference Status — The IREFST bit indicates the current source for the reference clock. The IREFST
bit does not update immediately after a write to the IREFS bit due to internal synchronization between clock
domains.
0 Source of reference clock is external reference clock (oscillator or external clock source as determined by the
1 Source of reference clock is internal reference clock.
Clock Mode Status — The CLKST bits indicate the current clock mode. The CLKST bits do not update
immediately after a write to the CLKS bits due to internal synchronization between clock domains.
00
01
10
11
EREFS bit in the MCGC2 register).
LOLS
Encoding 0 — Output of FLL is selected.
Encoding 1 — Internal reference clock is selected.
Encoding 2 — External reference clock is selected.
Encoding 3 — Output of PLL is selected.
7
0
0
Table 12-4. MCG Status and Control Register Field Descriptions
Figure 12-6. MCG Status and Control Register (MCGSC)
LOCK
0
0
6
unl
. LOLIE determines whether an interrupt request is made when set. LOLS is cleared by
MC9S08JM60 Series Data Sheet, Rev. 3
PLLST
0
0
5
IREFST
1
1
4
Description
0
0
3
CLKST
Multi-Purpose Clock Generator (S08MCGV1)
0
0
2
OSCINIT
0
0
1
FTRIM
U
0
0
189