MC9S08JM60CLH Freescale, MC9S08JM60CLH Datasheet - Page 197

• Manufacturer Part Number: MC9S08JM60CLH
• Manufacturer: Freescale

Specifications of MC9S08JM60CLH

• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 24MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 4KB
• # I/os (max): 51
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 12-chx12-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: LQFP
• Program Memory Type: Flash
• Program Memory Size: 60KB
• Lead Free Status / RoHS Status: Compliant

12.4.4
The low power bit (LP) is provided to allow the FLL or PLL to be disabled and thus conserve power when
these systems are not being used. However, in some applications it may be desirable to enable the FLL or
PLL and allow it to lock for maximum accuracy before switching to an engaged mode. Do this by writing
the LP bit to 0.
12.4.5
When IRCLKEN is set the internal reference clock signal will be presented as MCGIRCLK, which can be
used as an additional clock source. The MCGIRCLK frequency can be re-targeted by trimming the period
of the internal reference clock. This can be done by writing a new value to the TRIM bits in the MCGTRM
register. Writing a larger value will decrease the MCGIRCLK frequency, and writing a smaller value to
the MCGTRM register will increase the MCGIRCLK frequency. The TRIM bits will effect the MCGOUT
frequency if the MCG is in FLL engaged internal (FEI), FLL bypassed internal (FBI), or bypassed low
power internal (BLPI) mode. The TRIM and FTRIM value is initialized by POR but is not affected by
other resets.
Until MCGIRCLK is trimmed, programming low reference divider (RDIV) factors may result in
MCGOUT frequencies that exceed the maximum chip-level frequency and violate the chip-level clock
timing specifications (see the
If IREFSTEN and IRCLKEN bits are both set, the internal reference clock will keep running during stop
mode in order to provide a fast recovery upon exiting stop.
12.4.6
The MCG module can support an external reference clock with frequencies between 31.25 kHz to 5 MHz
in FEE and FBE modes, 1 MHz to 16 MHz in PEE and PBE modes, and 0 to 40 MHz in BLPE mode.
When ERCLKEN is set, the external reference clock signal will be presented as MCGERCLK, which can
be used as an additional clock source. When IREFS = 1, the external reference clock will not be used by
the FLL or PLL and will only be used as MCGERCLK. In these modes, the frequency can be equal to the
maximum frequency the chip-level timing specifications will support (see the
If EREFSTEN and ERCLKEN bits are both set or the MCG is in FEE, FBE, PEE, PBE or BLPE mode,
the external reference clock will keep running during stop mode in order to provide a fast recovery upon
exiting stop.
If CME bit is written to 1, the clock monitor is enabled. If the external reference falls below a certain
frequency (f
LOC bit in the System Reset Status (SRS) register will be set to indicate the error.
12.4.7
The MCG presents the divided reference clock as MCGFFCLK for use as an additional clock source. The
MCGFFCLK frequency must be no more than 1/4 of the MCGOUT frequency to be valid. Because of this
requirement, the MCGFFCLK is not valid in bypass modes for the following combinations of BDIV and
RDIV values:
Freescale Semiconductor
Low Power Bit Usage
Internal Reference Clock
External Reference Clock
Fixed Frequency Clock
loc_high
or f
loc_low
Device Overview
depending on the RANGE bit in the MCGC2), the MCU will reset. The
MC9S08JM60 Series Data Sheet, Rev. 3
chapter).
Multi-Purpose Clock Generator (S08MCGV1)
Device Overview
chapter).
197