MC9S08JM60CLH Freescale, MC9S08JM60CLH Datasheet - Page 58

• Manufacturer Part Number: MC9S08JM60CLH
• Manufacturer: Freescale

Specifications of MC9S08JM60CLH

• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 24MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 4KB
• # I/os (max): 51
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 12-chx12-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: LQFP
• Program Memory Type: Flash
• Program Memory Size: 60KB
• Lead Free Status / RoHS Status: Compliant

Chapter 4 Memory
is no way to disengage security without completely erasing all flash locations. If KEYEN is 1, a secure
user program can temporarily disengage security by:
The security key can be written only from secure memory (either RAM or flash), so it cannot be entered
through background commands without the cooperation of a secure user program.
The backdoor comparison key (NVBACKKEY through NVBACKKEY+7) is located in flash memory
locations in the nonvolatile register space so users can program these locations exactly as they would
program any other flash memory location. The nonvolatile registers are in the same 512-byte block of flash
as the reset and interrupt vectors, so block protecting that space also block protects the backdoor
comparison key. Block protects cannot be changed from user application programs, so if the vector space
is block protected, the backdoor security key mechanism cannot permanently change the block protect,
security settings, or the backdoor key.
Security can always be disengaged through the background debug interface by taking these steps:
4.7
The flash module has nine 8-bit registers in the high-page register space, three locations in the nonvolatile
register space in flash memory which are copied into three corresponding high-page control registers at
reset. There is also an 8-byte comparison key in flash memory. Refer to
absolute address assignments for all flash registers. This section refers to registers and control bits only by
their names. A Freescale-provided equate or header file normally is used to translate these names into the
appropriate absolute addresses.
58
1. Writing 1 to KEYACC in the FCNFG register. This makes the flash module interpret writes to the
2. Writing the user-entered key values to the NVBACKKEY through NVBACKKEY+7 locations.
3. Writing 0 to KEYACC in the FCNFG register. If the 8-byte key that was just written matches the
1. Disable any block protections by writing FPROT. FPROT can be written only with background
2. Mass erase flash if necessary.
3. Blank check flash. Provided flash is completely erased, security is disengaged until the next reset.
backdoor comparison key locations (NVBACKKEY through NVBACKKEY+7) as values to be
compared against the key rather than as the first step in a flash program or erase command.
These writes must be done in order starting with the value for NVBACKKEY and ending with
NVBACKKEY+7. STHX must not be used for these writes because these writes cannot be done
on adjacent bus cycles. User software normally would get the key codes from outside the MCU
system through a communication interface such as a serial I/O.
key stored in the flash locations, SEC01:SEC00 are automatically changed to 1:0 and security will
be disengaged until the next reset.
debug commands, not from application software.
To avoid returning to secure mode after the next reset, program NVOPT so SEC01:SEC00 = 1:0.
Flash Registers and Control Bits
MC9S08JM60 Series Data Sheet, Rev. 3
Table 4-3
and
Freescale Semiconductor
Table 4-4
for the