ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 107

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.12.8 TRX_CTRL_1 – Transceiver Control Register 1
9.12.9 PHY_TX_PWR – Transceiver Transmit Power Control Register
8266B-MCU Wireless-03/11
The TRX_CTRL_1 register is a multi purpose register to control various operating
modes and settings of the radio transceiver.
• Bit 7 – PA_EXT_EN - External PA support enable
This register bit enables pin DIG3 and pin DIG4 to indicate the transmit state of the
radio transceiver. The control of the external RF front-end is disabled when this bit is 0.
Both pins DIG3 and DIG4 are then low. The control of the external front-end is enabled
when this bit is 1. DIG3 and DIG4 then indicate the state of the radio transceiver. Pin
DIG3 is high and pin DIG4 is low in the state TX_BUSY. In all other states pin DIG3 is
low and pin DIG4 is high. It is recommended to set PA_EXT_EN=1 only in receive or
transmit states to reduce the power consumption or avoid leakage current of external
RF switches or other building blocks especially during SLEEP state.
• Bit 6 – IRQ_2_EXT_EN - Connect Frame Start IRQ to TC1
When this bit is set to one the capture input of Timer/Counter 1 is connected to the RX
frame start signal and pin DIG2 becomes an output, driving the RX frame start signal.
Antenna Diversity RF switch control (ANT_EXT_SW_EN=1) shall not be used at the
same time, because it shares the same device pin. The function IRQ_2_EXT_EN is
available for alternate frame time stamping using Timer/Counter 1. In general the
preferred method for frame time stamping is using the symbol counter.
• Bit 5 – TX_AUTO_CRC_ON - Enable Automatic CRC Calculation
This register bit controls the automatic FCS generation for TX operations. The
automatic FCS algorithm is performed autonomously by the radio transceiver if register
bit TX_AUTO_CRC_ON=1.
• Bit 4:0 – Res4:0 - Reserved
This register controls the output power of the transmitter.
Bit
NA ($144)
Read/Write
Initial Value
Bit
NA ($144)
Read/Write
Initial Value
Bit
NA ($145)
Read/Write
Initial Value
Bit
NA ($145)
Read/Write
Initial Value
PA_BUF_LT1
PA_EXT_EN
TX_PWR3
Res3
RW
RW
RW
7
0
R
3
0
7
1
3
0
IRQ_2_EXT_EN TX_AUTO_CRC_ON
PA_BUF_LT0
TX_PWR2
RW
Res2
RW
RW
6
0
R
2
0
6
1
2
0
TX_PWR1
PA_LT1
Res1
RW
RW
RW
R
1
0
5
0
1
0
5
1
ATmega128RFA1
TX_PWR0
PA_LT0
Res0
RW
RW
R
0
0
4
0
0
0
Res4
R
4
0
PHY_TX_PWR
PHY_TX_PWR
TRX_CTRL_1
TRX_CTRL_1
107