ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 231

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

17.6 Compare Match Output Unit
17.6.1 Compare Output Mode and Waveform Generation
8266B-MCU Wireless-03/11
Be aware that the COM0x1:0 bits are not double buffered together with the compare
value. A Change of the COM0x1:0 bits will take effect immediately.
The Compare Output mode (COM0x1:0) bits have two functions. The Waveform
Generator uses the COM0x1:0 bits for defining the Output Compare (OC0x) state at the
next Compare Match. The COM0x1:0 bits control also the OC0x pin output source.
Figure 17-4 shows a simplified schematic of the logic affected by the COM0x1:0 bit
setting. The I/O Registers, I/O bits and I/O pins in the figure are shown in bold. Only the
parts of the general I/O Port Control Registers (DDR and PORT) affected by the
COM0x1:0 bits are shown. When referring to the OC0x state, the reference is to the
internal OC0x Register and not to the OC0x pin. The OC0x Register is reset to “0” if a
system reset occurs.
Figure 17-4. Compare Match Output Unit Schematic
The general I/O port function is overridden by the Output Compare (OC0x) from the
Waveform Generator if either of the COM0x1:0 bits are set. However the OC0x pin
direction (input or output) is still controlled by the Data Direction Register (DDR) of the
port pin. The Data Direction Register bit of the OC0x pin (DDR_OC0x) must be set as
output before the OC0x value is visible at the pin. The port override function is
independent of the Waveform Generation mode.
The design of the Output Compare pin logic allows initializing the OC0x state before the
output is enabled. Note that some COM0x1:0 bit settings are reserved for certain
modes of operation (see
The Waveform Generator uses the COM0x1:0 bits differently in Normal, CTC and PWM
modes. A setting of COM0x1:0 = 0 tells the Waveform Generator in all modes that no
action on the OC0x Register is to be performed on the next Compare Match. For
compare output actions in the non-PWM modes refer to Table 17-2. For fast PWM
mode refer to Table 17-3 and for phase correct PWM refer to Table 17-4.
COMnx1
COMnx0
FOCn
clk
I/O
Waveform
Generator
"Register Description" on
D
D
D
PORT
DDR
OCnx
Q
Q
Q
page 239).
ATmega128RFA1
1
0
OCnx
Pin
231