ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 87

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.8.2 High Data Rate Modes
9.8.2.1 Overview
9.8.2.2 High Data Rate Packet Structure
8266B-MCU Wireless-03/11
• Generate random values for AES key generation (see
The values are stored in bits RND_VALUE of register PHY_RSSI. The random number
is updated every t
Note, if the PLL is not locked or unlocks in receive states, the RND_VALUE is zero.
The main features of the High Data Rate Modes are:
• High Data Rate Communication up to 2 Mb/s;
• Support of Basic and Extended Operating Mode;
• Support of other features of the Extended Feature Set;
The radio transceiver also supports alternative data rates higher than 250 kb/s for
applications beyond IEEE 802.15.4 compliant networks.
The selection of a data rate does not affect the remaining functionality. Thus it is
possible to run all features and operating modes of the radio transceiver in various
combinations.
The data rate can be selected by writing bits OQPSK_DATA_RATE of register
TRX_CTRL_2.
The High Data Rate Modes occupy the same RF channel bandwidth as the
IEEE 802.15.4 – 2.4 GHz 250 kb/s standard mode. The sensitivity of the receiver is
reduced due to the decreased spreading factor. The following table shows typical
values of the sensitivity for different data rates.
Table 9-23. High Data Rate Sensitivity
By default there is no header based signaling of the data rate within a transmitted
frame. Thus nodes using a data rate other than the default IEEE 802.15.4 data rate of
250 kb/s are to be consistently configured in advance. The configurable start of frame
delimiter (SFD) could be alternatively used as an indicator of the PHY data rate (see
"Configurable Start-Of-Frame Delimiter (SFD)" on
Higher data rate modulation is restricted to only the payload octets in order to allow
appropriate frame synchronization. The SHR and the PHR field are transmitted with the
IEEE 802.15.4 compliant data rate of 250 kb/s (refer to
2006 Frame Format" on page
A comparison of the general packet structure for different data rates with an example
PSDU length of 80 octets is shown in
page
High Data Rate
1000 kb/s
2000 kb/s
93);
250 kb/s
500 kb/s
TR29
= 1 µs in Basic Operation Mode receive states with locked PLL.
-100 dBm
-9 dBm
-9 dBm
-8 dBm
Sensitivity
62).
Figure 9-30 on
Comment
PER
PER
PER
PER
1%, PSDU length of 20 octets
1%, PSDU length of 20 octets
1%, PSDU length of 20 octets
1%, PSDU length of 20 octets
page 92).
ATmega128RFA1
page 88.
"Introduction – IEEE 802.15.4-
"Security Module (AES)" on
87