ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 169

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.6.3 PRR1 – Power Reduction Register 1
8266B-MCU Wireless-03/11
• Bit 5 – PRTIM0 - Power Reduction Timer/Counter0
Writing a logic one to this bit shuts down the Timer/Counter0 module. When the
Timer/Counter0 is enabled, operation will continue like before the shutdown.
• Bit 4 – PRPGA - Power Reduction PGA
Writing a logic one to this bit reduced the power consumption of the programmable gain
amplifier. The block is not turned off. Only the current levels in the amplifiers are
reduced. Reducing the PGA current levels is only recommended for slow ADC clock
frequencies. A new ADC conversion using the PGA should be delayed by a default
start-up time after changing (setting or resetting) this bit.
• Bit 3 – PRTIM1 - Power Reduction Timer/Counter1
Writing a logic one to this bit shuts down the Timer/Counter1 module. When the
Timer/Counter1 is enabled, operation will continue like before the shutdown.
• Bit 2 – PRSPI - Power Reduction Serial Peripheral Interface
Writing a logic one to this bit shuts down the Serial Peripheral Interface by stopping the
clock to the module. When waking up the SPI again, the SPI should be re initialized to
ensure proper operation.
• Bit 1 – PRUSART0 - Power Reduction USART
Writing a logic one to this bit shuts down the USART0 by stopping the clock to the
module. When waking up the USART0 again, the USART0 should be reinitialized to
ensure proper operation.
• Bit 0 – PRADC - Power Reduction ADC
Writing a logic one to this bit shuts down the ADC. The ADC must be disabled (reset
ADEN bit in register ADCSRA) before shut down. The analog comparator cannot use
the ADC input MUX when the ADC is shut down.
• Bit 7 – Res - Reserved Bit
This bit is reserved for future use. A read access always will return zero. A write access
does not modify the content.
• Bit 6 – PRTRX24 - Power Reduction Transceiver
Writing a logic one to this bit shuts down the transceiver (disconnect from the power
supply). In power-down and power-save modes the power-chain will be disabled when
this bit is one. Writing a logic zero to this bit will re-enable the transceiver.
• Bit 5 – PRTIM5 - Power Reduction Timer/Counter5
Writing a logic one to this bit shuts down the Timer/Counter5 module. When the
Timer/Counter5 is enabled, operation will continue like before the shutdown.
• Bit 4 – PRTIM4 - Power Reduction Timer/Counter4
Writing a logic one to this bit shuts down the Timer/Counter4 module. When the
Timer/Counter4 is enabled, operation will continue like before the shutdown.
Bit
NA ($65)
Read/Write
Initial Value
Res
R
7
0
PRTRX24 PRTIM5
RW
6
0
RW
5
0
PRTIM4
RW
4
0
PRTIM3
RW
3
0
ATmega128RFA1
2
1
PRUSART1
RW
0
0
PRR1
169