ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 38

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.4.1.2.3 PLL_ON – PLL State
9.4.1.2.4 RX_ON and BUSY_RX – RX Listen and Receive State
9.4.1.2.5 BUSY_TX – Transmit State
38
ATmega128RFA1
Entering the PLL_ON state from TRX_OFF state first enables the analog voltage
regulator (AVREG). After the voltage regulator has been settled the PLL frequency
synthesizer is enabled. When the PLL has been settled at the receive frequency to a
channel defined by bits CHANNEL of register PHY_CC_CCA a successful PLL lock is
indicated by issuing a TRX24_PLL_LOCK interrupt.
If an RX_ON command is issued in PLL_ON state, the receiver is immediately enabled.
If the PLL has not been settled before the state change nevertheless takes place. Even
if the register bits TRX_STATUS of register TRX_STATUS indicates RX_ON, actual
frame reception can only start once the PLL has locked.
The PLL_ON state corresponds to the TX_ON state in IEEE 802.15.4.
In RX_ON state the receiver blocks and the PLL frequency synthesizer are enabled.
The receive mode is internally separated into the RX_ON and BUSY_RX states. There
is no difference between these states with respect to the analog radio transceiver
circuitry, which are always turned on. In both states the receiver and the PLL frequency
synthesizer are enabled.
During RX_ON state the receiver listens for incoming frames. After detecting a valid
synchronization header (SHR), the receiver automatically enters the BUSY_RX state.
The reception of a valid PHY header (PHR) generates an TRX24_RX_START interrupt
and receives and demodulates the PSDU data.
During PSDU reception the frame data are stored continuously in the Frame Buffer until
the last byte was received. The completion of the frame reception is indicated by an
TRX24_RX_END interrupt and the radio transceiver reenters the state RX_ON. At the
same time the bits RX_CRC_VALID of register PHY_RSSI are updated with the result
of the FCS check (see
Received frames are passed to the frame filtering unit, refer to section
on
IEEE 802.15.4 section 7.2.1) matches to the expected addresses, which is further
dependent on the addressing mode, an address match interrupt (TRX24_XAH_AMI) is
issued, refer to
stored in the registers Short-Address, PAN-ID and IEEE-address. Frame filtering is
available in Basic and Extended Operating Mode, refer to section
page 55.
Leaving state RX_ON is only possible by writing a state change command to bits
TRX_CMD of register TRX_STATE.
A transmission can only be initiated in state PLL_ON. There are two ways to start a
transmission:
• Setting Bit SLPTR of register TRXPR to ‘1’. The bit should be cleared before the
• TX_START command to bits TRX_CMD of register TRX_STATE.
Either of these causes the radio transceiver into the BUSY_TX state.
frame has been transmitted. This mode is for legacy operation and should be
replaced by the TX_START command below.
page 55. If the content of the MAC addressing fields of a frame
"Interrupt Logic" on page
"Frame Check Sequence (FCS)" on page 67).
34. The expected address values are to be
"Frame Filtering" on
8266B-MCU Wireless-03/11
"Frame Filtering"
(refer to