ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 123

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.12.27 PLL_DCU – Transceiver Delay Cell Calibration Control Register
9.12.28 PART_NUM – Device Identification Register (Part Number)
8266B-MCU Wireless-03/11
This register controls the operation of the center frequency calibration loop.
• Bit 7 – PLL_CF_START - Start Center Frequency Calibration
PLL_CF_START = 1 initiates the center frequency calibration. The calibration cycle has
finished after 35 µs (typical). The register bit is cleared immediately after finishing the
calibration.
• Bit 6:0 – Resx6:0 - Reserved
This register controls the operation of the calibration loop of the delay cell.
• Bit 7 – PLL_DCU_START - Start Delay Cell Calibration
PLL_DCU_START = 1 initiates the delay cell calibration. The calibration cycle has
finished after at most 6 µs. The register bit is cleared immediately after finishing the
calibration.
• Bit 6:0 – Resx6:0 - Reserved
This register contains the part number of the device.
• Bit 7:0 – PART_NUM7:0 - Part Number
These bits decode the part number of the device according to the following table.
Bit
NA ($15A)
Read/Write
Initial Value
Bit
NA ($15A)
Read/Write
Initial Value
Bit
NA ($15B)
Read/Write
Initial Value
Bit
NA ($15B)
Read/Write
Initial Value
Bit
NA ($15C)
Read/Write
Initial Value
PLL_DCU_START
R
7
1
Resx3
RW
RW
3
0
7
0
R
6
0
Resx3
Resx1
RW
RW
3
0
1
1
R
5
0
Resx2
Resx6
RW
2
0
R
6
0
PART_NUM7:0
R
4
0
R
3
0
Resx1
Resx5
RW
RW
1
0
5
1
R
2
0
Resx2
Resx0
ATmega128RFA1
RW
RW
2
1
0
1
R
1
1
Resx0
Resx4
RW
RW
0
0
4
0
R
0
1
PART_NUM
PLL_DCU
PLL_CF
PLL_CF
PLL_DCU
123