ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 164

IC AVR MCU 2.4GHZ XCEIVER 64QFN

ATMEGA128RFA1-ZU

Manufacturer Part Number
ATMEGA128RFA1-ZU
Description
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer
Atmel
Series
ATMEGAr

Specifications of ATMEGA128RFA1-ZU

Frequency
2.4GHz
Data Rate - Maximum
2Mbps
Modulation Or Protocol
802.15.4 Zigbee
Applications
General Purpose
Power - Output
3.5dBm
Sensitivity
-100dBm
Voltage - Supply
1.8 V ~ 3.6 V
Current - Receiving
12.5mA
Current - Transmitting
14.5mA
Data Interface
PCB, Surface Mount
Memory Size
128kB Flash, 4kB EEPROM, 16kB RAM
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
64-VFQFN, Exposed Pad
Rf Ic Case Style
QFN
No. Of Pins
64
Supply Voltage Range
1.8V To 3.6V
Operating Temperature Range
-40°C To +85°C
Svhc
No SVHC (15-Dec-2010)
Rohs Compliant
Yes
Processor Series
ATMEGA128x
Core
AVR8
Data Bus Width
8 bit
Program Memory Type
Flash
Program Memory Size
128 KB
Data Ram Size
16 KB
Interface Type
JTAG
Maximum Clock Frequency
16 MHz
Number Of Programmable I/os
38
Number Of Timers
6
Operating Supply Voltage
1.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVR128RFA1-EK1
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA128RFA1-ZU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATMEGA128RFA1-ZUR
Manufacturer:
ON
Quantity:
56 000
12.5.4 Low Leakage Voltage Regulator (LLVREG)
164
ATmega128RFA1
• Low dropout (LDO) voltage regulator;
• Configurable to use an external voltage regulator;
The internal voltage regulators supply a stabilized voltage to the ATmega128RFA1. The
AVREG provides the regulated 1.8V supply voltage for the analog section and the
DVREG supplies the 1.8V supply voltage for the digital section. The DVREG is enabled
during startup and is switched off if the power-chain is disabled. The AVREG is enabled
only on request by either the A/D converter or the radio transceiver.
A simplified schematic of the internal voltage regulator is shown in
Figure 12-4. Simplified Schematic of AVREG/DVREG
The voltage regulators require bypass capacitors for stable operation. The value of the
bypass capacitors determines their settling time. The bypass capacitors shall be placed
as close as possible to the pins and shall be connected to ground with the shortest
possible traces.
The voltage regulators can be configured with the register VREG_CTRL. It is
recommended to use the internal regulators but it is also possible to supply the low
voltage domains by an external voltage supply. For this configuration the internal
regulators need to be switched off by setting the register bits to the values
AVREG_EXT = 1 and DVREG_EXT = 1 (see
Control and Status Register" on page
must then be connected to the pins 13, 14 (DVDD) and pin 29 (AVDD). When turning
on the external supply ensure a sufficiently long stabilization time before interacting with
the ATmega128RFA1.
The status bits AVDD_OK = 1 and DVDD_OK = 1 of register VREG_CTRL indicate an
enabled and stable internal supply voltage. Reading value 0 indicates that the internal
supply voltage is disabled or not yet settled to the final value.
Note that disabling the digital voltage regulator by DVREG_EXT bit is for internal use
only.
The main digital voltage regulator (DVREG) will be switched off during the deep sleep
modes “power-down” and “power-save”. The Low Leakage Voltage Regulator will then
keep the digital supply voltage to provide data retention. No application software control
is required.
During the active power states, when the main voltage regulator supplies the chip, the
Low Leakage Voltage Regulator is digitally calibrated. Its output voltage is adjusted to
match the output voltage of the main regulator. This fixed calibration result is stored and
used when the chip enters a power-down state where the main regulator is switched off.
reference
B andgap
voltage
1 .25 V
(D )E V D D
115). A regulated external supply voltage of 1.8V
A V D D ,
D V D D
"VREG_CTRL – Voltage Regulator
Figure 12-4
8266A-MCU Wireless-12/09
below.

Related parts for ATMEGA128RFA1-ZU