ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 491

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

31.9.18 Programming the EEPROM
31.9.19 Reading the EEPROM
31.9.20 Programming the Fuses
8266A-MCU Wireless-12/09
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash read using programming instruction 3a.
3. Load the page address using programming instructions 3c and 3d. PCWORD (refer
4. Enter JTAG instruction PROG_PAGEREAD.
5. Read the entire page (or Flash) by shifting out all instruction words in the page (or
6. Enter JTAG instruction PROG_COMMANDS.
7. Repeat steps 3 to 6 until all data have been read.
Before programming the EEPROM a Chip Erase must be performed, see
Chip Erase" on
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable EEPROM write using programming instruction 4a.
3. Load High byte of address using programming instruction 4b.
4. Load Low byte of address using programming instruction 4c.
5. Load data using programming instructions 4d and 4e.
6. Repeat steps 4 and 5 for all data bytes in the page.
7. Write the data using programming instruction 4f.
8. Poll for EEPROM write complete using programming instruction 4g, or wait for t
9. Repeat steps 3 to 8 until all data have been programmed.
Note that the PROG_PAGELOAD instruction can not be used when programming the
EEPROM.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable EEPROM read using programming instruction 5a.
3. Load address using programming instructions 5b and 5c.
4. Read data using programming instruction 5d.
5. Repeat steps 3 and 4 until all data have been read.
Note that the PROG_PAGEREAD instruction can not be used when reading the
EEPROM.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Fuse write using programming instruction 6a.
3. Load data high byte using programming instructions 6b. A bit value of “0” will
4. Write Fuse High byte using programming instruction 6c.
to
as 0.
Flash), starting with the LSB of the first instruction in the page (Flash) and ending
with the MSB of the last instruction in the page (Flash). The Capture-DR state both
captures the data from the Flash, and also auto-increments the program counter
after each word is read. Note that Capture-DR comes before the shift-DR state.
Hence, the first byte which is shifted out contains valid data.
(refer to
program the corresponding fuse; a “1” will un-program the fuse.
Table 31-7 on
Table 31-14 on
page 490.
page 467) is used to address within one page and must be written
page 477).
ATmega128RFA1
"Performing
WLRH
491