ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 377

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

25 2-wire Serial Interface
25.1 Features
25.2 2-wire Serial Interface Bus Definition
25.2.1 TWI Terminology
8266A-MCU Wireless-12/09
• Simple yet powerful and flexible communication interface, only two bus lines
• Both master and slave operation supported
• Device can operate as transmitter or receiver
• 7-bit address space allows up to 128 different slave addresses
• Multi-master arbitration support
• Up to 400 kHz data transfer speed
• Slew-rate limited output drivers
• Noise suppression circuitry rejects spikes on bus lines
• Fully programmable slave address with general call support
• Address recognition causes wake-up when microcontroller is in sleep mode
The 2-wire Serial Interface (TWI) is ideally suited for typical microcontroller applications.
The TWI protocol allows the systems designer to interconnect up to 128 different
devices using only two bi-directional bus lines, one for clock (SCL) and one for data
(SDA). The only external hardware needed to implement the bus is a single pull-up
resistor for each of the TWI bus lines. All devices connected to the bus have individual
addresses, and mechanisms for resolving bus contention are inherent in the TWI
protocol.
Figure 25-1. TWI Bus Interconnection
SDA
SCL
The following definitions are frequently encountered in this section.
Table 25-1. TWI Terminology
Term
Master
Slave
Transmitter
Receiver
needed
Device 1
Description
The device that initiates and terminates a transmission. The Master also
generates the SCL clock.
The device addressed by a Master.
The device placing data on the bus.
The device reading data from the bus.
Device 2
Device 3
........
Device n
DEVDD
ATmega128RFA1
R1
R2
377