ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 36

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.4.1.2 Basic Operating Mode Description
9.4.1.2.1 SLEEP – Sleep State
9.4.1.2.2 TRX_OFF – Clock State
36
ATmega128RFA1
Bit SLPTR is a multifunctional bit (refer to section
page 32
transition on SLPTR causes the following state transitions:
• TRX_OFF
• PLL_ON
Whereas resetting bit SLPTR to “0” causes the following state transitions:
• SLEEP
Bit TRXRST causes a reset of all radio transceiver registers and forces the radio
transceiver into TRX_OFF state.
For all states except SLEEP, the state change commands FORCE_TRX_OFF or
TRX_OFF lead to a transition into TRX_OFF state. If the radio transceiver is in active
receive or transmit states (BUSY_*), the command FORCE_TRX_OFF interrupts these
active processes, and forces an immediate transition to TRX_OFF. In contrast a
TRX_OFF command is stored until an active state (receiving or transmitting) has been
finished. After that the transition to TRX_OFF is performed.
For a fast transition from receive or active transmit states to PLL_ON state the
command FORCE_PLL_ON is provided. In contrast to FORCE_TRX_OFF this
command does not disable the PLL and the analog voltage regulator AVREG. It is not
available in states SLEEP, and RESET.
The completion of each requested state-change shall always be confirmed by reading
the bits TRX_STATUS of register TRX_STATUS.
In radio transceiver SLEEP state, the entire radio transceiver is disabled. No circuitry is
operating. The radio transceiver’s current consumption is reduced to leakage current
only. This state can only be entered from state TRX_OFF, by setting the bit
SLPTR = “1”.
Setting SLPTR = “0” returns the radio transceiver to the TRX_OFF state. During radio
transceiver SLEEP the register contents remains valid while the content of the Frame
Buffer and the security engine (AES) are cleared.
TRXRST = “1” in SLEEP state returns the radio transceiver to TRX_OFF state and
thereby sets all registers to their reset values.
This state is reached immediately after Power On or Reset. In TRX_OFF the crystal
oscillator is running. The digital voltage regulator is enabled, thus the radio transceiver
registers, the Frame Buffer and security engine (AES) are accessible (see section
"Frame Buffer" on page 77
SLPTR and TRXRST in register TRXPR can be used for state control (see
Control" on page 35
Entering the TRX_OFF state from radio transceiver SLEEP, or RESET state is
indicated by the TRX24_AWAKE interrupt.
for more details). Dependent on the radio transceiver state, a “0” to “1”
SLEEP
BUSY_TX
TRX_OFF
for details). The analog front-end is disabled during TRX_OFF.
and
"Security Module (AES)" on page
"Transceiver Pin Register TRXPR" on
92).
8266A-MCU Wireless-12/09
"State