ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 80

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.6.4.4 Interrupt Handling
9.6.5 Crystal Oscillator (XOSC)
9.6.5.1 Overview
9.6.5.2 Integrated Oscillator Setup
80
ATmega128RFA1
The value BATMON_OK should be read out to verify the current supply voltage value
after setting a new threshold.
Note:
A supply voltage drop below the configured threshold value is indicated by the
BAT_LOW interrupt. The BAT_LOW status bit as well as the BATLOW_EN bit is
located in the BATMON register. If BATLOW_EN =0, no IRQ is issued, but the status
flag is set if the battery low event occurs.
The interrupt is only issued if BATMON_OK changes from 1 to 0 and the event is stored
until the IRQ handler is called or the BAT_LOW IRQ is cleared manually by writing ‘1’ to
the BAT_LOW status flag.
No interrupt is generated when:
• The battery voltage is below the default 1.8V threshold at power up (BATMON_OK
• A new threshold is set which is still above the current supply voltage (BATMON_OK
Noise or temporary voltage drops may generate unwanted interrupts when the battery
voltage is close to the programmed threshold voltage. To avoid this:
• Disable the BAT_LOW interrupt with the BATLOW_EN Bit in the BATMON register
• Set a lower threshold value.
The main features of the crystal oscillator are:
• Amplitude controlled 16 MHz generation;
• 215 µs typical settling time after leaving SLEEP state;
• Configurable trimming with a capacitance array;
The crystal oscillator generates the reference frequency for the radio transceiver. All
other internally generated frequencies of the radio transceiver are derived from this
unique frequency. The overall system performance is therefore critically determined by
the accuracy of the crystal reference frequency. The external components of the crystal
oscillator should be selected carefully and the related board layout should be done with
caution as described in section
The register XOSC_CTRL provides access to the control signals of the oscillator. Two
operating modes are supported. It is recommended to use the integrated oscillator
setup as described in
be fed to the internal circuitry by using an external clock reference as shown in
9-26 on page
The output frequency of the internal oscillator depends on the load capacitance
between the crystal pins XTAL1 and XTAL2. The total load capacitance C
equal to the specified load capacitance of the crystal itself. It consists of the external
capacitors CX and parasitic capacitances connected to the XTAL nodes.
was never 1) or
remains 0).
and treat the battery as empty or
The battery monitor is inactive during SLEEP states. Refer to status register
TRX_STATUS for details.
82.
Figure 9-25 on
"Application Circuits" on page 493.
page 81. Nevertheless a reference frequency can
8266A-MCU Wireless-12/09
L
must be
Figure