AT32UC3L032-D3UR Atmel, AT32UC3L032-D3UR Datasheet - Page 189

• Manufacturer Part Number: AT32UC3L032-D3UR
• Description: MCU AVR32 32KB FLASH 48TLLGA
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3L032-D3UR

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TLLGA
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL
• Development Tools By Supplier: AT32UC3L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 9 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

32099F–11/2010
Coarse Value bit (DFLLnLOCKC) in PCLKSR will be set when this is done. In the FINE stage the
control logic tunes the value in DFLLnCONF.FINE so the output frequency will be very close to
the desired frequency. DFLLn Locked on Fine Value bit (DFLLnLOCKF) in PCLKSR will be set
when this is done. In the ACCURATE stage the DFLL frequency tuning mechanism uses dither-
ing on the FINE bits to obtain an accurate average output frequency. DFLLn Locked on Accurate
Value bit (DFLLnLOCKA) in PCLKSR will be set when this is done. The ACCURATE stage will
only be executed if the Dithering Enable bit (DITHER) in DFLLnCONF has been written to a one.
If DITHER is written to a zero DFLLnLOCKA will never occur. If dithering is enabled, the fre-
quency of the dithering is decided by a generic clock (CLK_DFLLIF_DITHER). This clock has to
be set up correctly before enabling dithering. Please refer to the Generic Clocks section for
details.
Figure 13-2. DFLL Closed-Loop State Diagram
When dithering is enabled the accuracy of the average output frequency of the DFLL will be
higher. However, the actual frequency will be alternating between two frequencies. If a fixed fre-
quency is required, the dithering should not be enabled.
DFLLnLOCKC
Calculate
COARSE
Measure
value
f
new
DFLLn
0
1
DFLLnLOCKF
new FINE
Calculate
value
0
1
Compen-
DITHER
sate for
drift
0
AT32UC3L016/32/64
1
DFLLnLOCKA
Calculate
dutycycle
dithering
new
0
1
Compen-
sate for
drift
189