AT32UC3L032-D3UR Atmel, AT32UC3L032-D3UR Datasheet - Page 365

• Manufacturer Part Number: AT32UC3L032-D3UR
• Description: MCU AVR32 32KB FLASH 48TLLGA
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3L032-D3UR

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TLLGA
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL
• Development Tools By Supplier: AT32UC3L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 9 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

19.6.2
19.6.3
19.6.3.1
32099F–11/2010
Receiver and Transmitter Control
Synchronous and Asynchronous Modes
Transmitter Operations
After reset, the receiver is disabled. The user must enable the receiver by setting the RXEN bit
in the Control Register (CR). However, the receiver registers can be programmed before the
receiver clock is enabled.
After reset, the transmitter is disabled. The user must enable it by setting the TXEN bit in the
Control Register (CR). However, the transmitter registers can be programmed before being
enabled.
The Receiver and the Transmitter can be enabled together or independently.
At any time, the software can perform a reset on the receiver or the transmitter of the USART by
setting the corresponding bit, RSTRX and RSTTX respectively, in the Control Register (CR).
The software resets clear the status flag and reset internal state machines but the user interface
configuration registers hold the value configured prior to software reset. Regardless of what the
receiver or the transmitter is performing, the communication is immediately stopped.
The user can also independently disable the receiver or the transmitter by setting RXDIS and
TXDIS respectively in CR. If the receiver is disabled during a character reception, the USART
waits until the end of reception of the current character, then the reception is stopped. If the
transmitter is disabled while it is operating, the USART waits the end of transmission of both the
current character and character being stored in the Transmit Holding Register (THR). If a time-
guard is programmed, it is handled normally.
The transmitter performs the same in both synchronous and asynchronous operating modes
(SYNC = 0 or SYNC = 1). One start bit, up to 9 data bits, one optional parity bit and up to two
stop bits are successively shifted out on the TXD pin at each falling edge of the programmed
serial clock.
The number of data bits is selected by the CHRL field and the MODE 9 bit in the Mode Register
(MR). Nine bits are selected by setting the MODE 9 bit regardless of the CHRL field. The parity
bit is set according to the PAR field in MR. The even, odd, space, marked or none parity bit can
be configured. The MSBF field in MR configures which data bit is sent first. If written at 1, the
most significant bit is sent first. At 0, the less significant bit is sent first. The number of stop bits is
selected by the NBSTOP field in MR. The 1.5 stop bit is supported in asynchronous mode only.
Figure 19-4. Character Transmit
The characters are sent by writing in the Transmit Holding Register (THR). The transmitter
reports two status bits in the Channel Status Register (CSR): TXRDY (Transmitter Ready),
which indicates that THR is empty and TXEMPTY, which indicates that all the characters written
Baud Rate
Example: 8-bit, Parity Enabled One Stop
Clock
TXD
Start
Bit
D0
D1
D2
D3
D4
AT32UC3L016/32/64
D5
D6
D7
Parity
Bit
Stop
Bit
365