AT32UC3L032-D3UR Atmel, AT32UC3L032-D3UR Datasheet - Page 428

• Manufacturer Part Number: AT32UC3L032-D3UR
• Description: MCU AVR32 32KB FLASH 48TLLGA
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3L032-D3UR

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TLLGA
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL
• Development Tools By Supplier: AT32UC3L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 9 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

20.5
20.6
20.6.1
20.6.2
20.6.3
20.7
20.7.1
32099F–11/2010
I/O Lines Description
Product Dependencies
Functional Description
I/O Lines
Clocks
Interrupts
Modes of Operation
Table 20-1.
In order to use this module, other parts of the system must be configured correctly, as described
below.
The pins used for interfacing the compliant external devices may be multiplexed with I/O lines.
The user must first configure the I/O Controller to assign the SPI pins to their peripheral
functions.
The clock for the SPI bus interface (CLK_SPI) is generated by the Power Manager. This clock is
enabled at reset, and can be disabled in the Power Manager. It is recommended to disable the
SPI before disabling the clock, to avoid freezing the SPI in an undefined state.
The SPI interrupt request line is connected to the interrupt controller. Using the SPI interrupt
requires the interrupt controller to be programmed first.
The SPI operates in master mode or in slave mode.
Operation in master mode is configured by writing a one to the Master/Slave Mode bit in the
Mode Register (MR.MSTR). The pins NPCS0 to NPCS3 are all configured as outputs, the SPCK
pin is driven, the MISO line is wired on the receiver input and the MOSI line driven as an output
by the transmitter.
If the MR.MSTR bit is written to zero, the SPI operates in slave mode. The MISO line is driven by
the transmitter output, the MOSI line is wired on the receiver input, the SPCK pin is driven by the
transmitter to synchronize the receiver. The NPCS0 pin becomes an input, and is used as a
Slave Select signal (NSS). The pins NPCS1 to NPCS3 are not driven and can be used for other
purposes.
The data transfers are identically programmable for both modes of operations. The baud rate
generator is activated only in master mode.
Pin Name
MISO
MOSI
SPCK
NPCS1-NPCS3
NPCS0/NSS
I/O Lines Description
Pin Description
Master In Slave Out
Master Out Slave In
Serial Clock
Peripheral Chip Selects
Peripheral Chip Select/Slave Select
AT32UC3L016/32/64
Master
Input
Output
Output
Output
Output
Type
Slave
Output
Input
Input
Unused
Input
428