AT32UC3L032-D3UR Atmel, AT32UC3L032-D3UR Datasheet - Page 313

• Manufacturer Part Number: AT32UC3L032-D3UR
• Description: MCU AVR32 32KB FLASH 48TLLGA
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3L032-D3UR

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TLLGA
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL
• Development Tools By Supplier: AT32UC3L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 9 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

17.5.1.1
17.5.2
17.5.3
32099F–11/2010
Measurement
Interrupts
Cautionary note
Note that if clock selected as source for CLK_REF is stopped during a measurement, this will
not be detected by the FREQM. The BUSY bit in the STATUS register will never be cleared, and
the DONE interrupt will never be triggered. If the clock selected as soruce for CLK_REF is
stopped, it will not be possible to change the source for the reference clock as long as the
selected source is not running.
In the Mode Register the Clock Source Selection (CLKSEL) field selects CLK_MSR and the
Number of Reference Clock Cycles (REFNUM) field selects the duration of the measurement.
The duration is given in number of CLK_REF periodes.
Writing a one to the START bit in the Control Register (CTRL) starts the measurement. The
BUSY bit in SR is cleared when the measurement is done.
The result of the measurement can be read from the Value Register (VALUE). The frequency of
the measured clock CLK_MSR is then:
The FREQM has two interrupt sources:
These will generate an interrupt request if the corresponding bit in the Interrupt Mask Register
(IMR) is set. The interrupt sources are ORed together to form one interrupt request. The FREQM
will generate an interrupt request if at least one of the bits in the Interrupt Mask Register (IMR) is
set. Bits in IMR are set by writing a one to the corresponding bit in the Interrupt Enable Register
(IER) and cleared by writing a one to this bit in the Interrupt Disable Register (IDR). The interrupt
request remains active until the corresponding bit in the Interrupt Status Register (ISR) is
cleared by writing a one to this bit in the Interrupt Clear Register (ICR). Because all the interrupt
sources are ORed together, the interrupt request from the FREQM will remain active until all the
bits in ISR are cleared.
• Write a zero to the MODE.REFCEN to disable he clock, without changing the other bits/fields
• Wait until the SR.RCLKBUSY bit reads as zero.
• DONE: A frequency measurement is done
• RCLKRDY: The reference clock is ready
in the Mode register.
f
CLK_MSR
= (VALUE/REFNUM)*f
CLK_REF
AT32UC3L016/32/64
313