AT32UC3L032-D3UR Atmel, AT32UC3L032-D3UR Datasheet - Page 333

• Manufacturer Part Number: AT32UC3L032-D3UR
• Description: MCU AVR32 32KB FLASH 48TLLGA
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3L032-D3UR

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TLLGA
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL
• Development Tools By Supplier: AT32UC3L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 9 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

18.7
18.7.1
32099F–11/2010
User Interface
Access Types
The GPIO controller manages all the GPIO pins on the 32-bit AVR microcontroller. The pins are
managed as 32-bit ports that are configurable through a Peripheral Bus (PB) interface. Each
port has a set of configuration registers. The overall memory map of the GPIO is shown below.
The number of pins and hence the number of ports is product specific.
Figure 18-6. Port Configuration Registers
In the peripheral muxing table in the Package and Pinout chapter each GPIO pin has a unique
number. Note that the PA, PB, PC, and PX ports do not necessarily directly correspond to the
GPIO ports. To find the corresponding port and pin the following formulas can be used:
GPIO port = floor((GPIO number) / 32), example: floor((36)/32) = 1
GPIO pin = GPIO number % 32, example: 36 % 32 = 4
Table 18-2
port address offset. The specific address of a configuration register is found by adding the regis-
ter offset and the port offset to the GPIO start address. One bit in each of the configuration
registers corresponds to a GPIO pin.
Most configuration register can be accessed in four different ways. The first address location can
be used to write the register directly. This address can also be used to read the register value.
The following addresses facilitate three different types of write access to the register. Performing
a “set” access, all bits written to one will be set. Bits written to zero will be unchanged by the
operation. Performing a “clear” access, all bits written to one will be cleared. Bits written to zero
will be unchanged by the operation. Finally, a toggle access will toggle the value of all bits writ-
shows the configuration registers for one port. Addresses shown are relative to the
Port 0 Configuration Registers
Port 1 Configuration Registers
Port 2 Configuration Registers
Port n Configuration Registers
AT32UC3L016/32/64
n*0x200
0x0000
0x0200
0x0400
333