AT32UC3L032-D3UR Atmel, AT32UC3L032-D3UR Datasheet - Page 603

• Manufacturer Part Number: AT32UC3L032-D3UR
• Description: MCU AVR32 32KB FLASH 48TLLGA
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3L032-D3UR

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TLLGA
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL
• Development Tools By Supplier: AT32UC3L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 9 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

26.6.3
26.6.4
26.6.5
32099F–11/2010
ADC Resolution
Enhanced Resolution Mode
Pseudorandom Noise Generator
The result of the conversion is stored in the Last Converted Data Register (LCDR) as they
become available, overwriting the result from the previous conversion. To avoid data loss if more
than one channel is enabled, the user must read the conversion results as they become avail-
able either by using an interrupt handler or by using a Peripheral DMA channel to copy the
results to memory. Failing to do so will result in an Overrun Error condition, indicated by the
OVRE bit in the Status Register (SR).
To use an interrupt handler the user must enable the Data Ready (DRDY) interrupt request by
writing a one to the corresponding bit in the Interrupt Enable Register (IER). To clear the inter-
rupt after the conversion result is read, the user must write a one to the corresponding bit in the
Interrupt Clear Register (ICR). See
To use a Peripheral DMA Controller channel the user must configure the Peripheral DMA Con-
troller appropriately. The Peripheral DMA Controller will, when configured, automatically read
converted data as they become available. There is no need to manually clear any bits in the
Interrupt Status Register as this is performed by the hardware. If an Overrun Error condition hap-
pens during DMA operation, the OVRE bit in the SR will be set.
The Analog-to-Digital Converter cell supports 8-bit or 10-bit resolution, which can be extended to
11-bit and 12-bit with the Enhanced Resolution Mode. The resolution is selected by writing the
selected resolution value to the RES field in the ADC Configuration Register (ACR). See
26.9.3.
By writing a zero to the RES field, the ADC switches to the lowest resolution and the conversion
results can be read in the eight lowest significant bits of the Last Converted Data Register
(LCDR). The four highest bits of the Last Converted Data (LDATA) field in the LCDR register
reads as zero. Writing a one to the RES field enables 10-bit resolution, the optimal resolution for
both sampling speed and accuracy. Writing two or three automatically enables Enhanced Reso-
lution Mode with 11-bit or 12-bit resolution, see
When a Peripheral DMA Controller channel is connected to the ADCIFB in 10-bit, 11-bit, or 12-
bit resolution mode, a transfer size of 16 bits must be used. By writing a zero to the RES field,
the destination buffers can be optimized for 8-bit transfers.
The Enhanced Resolution Mode is automatically enabled when 11-bit or 12-bit mode is selected
in the ADC Configuration Register (ACR). In this mode the ADCIFB will trade conversion perfor-
mance for accuracy by averaging multiple samples.
To be able to increase the accuracy by averaging multiple samples it is important that some
noise is present in the input signal. The noise level should be between one and two LSB peak-
to-peak to get good averaging performance.
The performance cost of enabling 11-bit mode is 4 ADC samples, which reduces the effective
ADC performance by a factor 4. For 12-bit mode this factor is 16. For 12-bit mode the effective
sample rate is maximum ADC sample rate divided by 16.
The Pseudorandom Noise Generator generates a random 1-bit signal (PRND) which can be
used to add noise to the analog input signals. This signal can be multiplexed out to a pad using
the I/O Controller and added to analog input signals through a resistor. By varying the size of the
resistor, the noise levels added can be adjusted for optimal performance.
Section 26.6.12
Section 26.6.4
for details.
AT32UC3L016/32/64
for details.
Section
603