AT32UC3L032-D3UR Atmel, AT32UC3L032-D3UR Datasheet - Page 36

• Manufacturer Part Number: AT32UC3L032-D3UR
• Description: MCU AVR32 32KB FLASH 48TLLGA
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3L032-D3UR

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TLLGA
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL
• Development Tools By Supplier: AT32UC3L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 9 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

6. Supply and Startup Considerations
6.1
6.1.1
6.1.2
6.1.3
32099F–11/2010
Supply Considerations
Power Supplies
Voltage Regulator
Regulator Connection
The AT32UC3L has several types of power supply pins:
The ground pins GND are common to VDDCORE, VDDIO, and VDDIN. The ground pin for
VDDANA is GNDANA.
When VDDCORE is not connected to VDDIN, the VDDIN voltage must be higher than 1.98V.
Refer to
For decoupling recommendations for the different power supplies, please refer to the schematic
checklist.
The AT32UC3L embeds a voltage regulator that converts from 3.3V nominal to 1.8V with a load
of up to 60mA. The regulator supplies the output voltage on VDDCORE. The regulator may only
be used to drive internal circuitry in the device. VDDCORE should be externally connected to the
1.8V domains. See
Adequate output supply decoupling is mandatory for VDDCORE to reduce ripple and avoid
oscillations. The best way to achieve this is to use two capacitors in parallell between
VDDCORE and GND as close to the chip as possible. Please refer to
796
Figure 6-1.
The AT32UC3L supports three power supply configurations:
3.3V
1.8V
•VDDIO: Powers I/O lines. Voltage is 1.8 to 3.3V nominal.
•VDDIN: Powers I/O lines and the internal regulator. Voltage is 1.8 to 3.3V nominal.
•VDDANA: Powers the ADC. Voltage is 1.8V nominal.
•VDDCORE: Powers the core, memories, and peripherals. Voltage is 1.8V nominal.
• 3.3V single supply mode
• 1.8V single supply mode
• 3.3V supply mode, with 1.8V regulated I/O lines
for decoupling capacitors values and regulator characteristics.
Section 32. on page 782
Supply Decoupling
C
Section 6.1.3
IN3
C
C
for regulator connection figures.
OUT2
for power consumption on the various supply pins.
IN2
C
C
OUT1
IN1
VDDCORE
AT32UC3L016/32/64
VDDIN
Section 32.9.1 on page
Regulator
1.8V
36