AT32UC3L032-D3UR Atmel, AT32UC3L032-D3UR Datasheet - Page 828

• Manufacturer Part Number: AT32UC3L032-D3UR
• Description: MCU AVR32 32KB FLASH 48TLLGA
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3L032-D3UR

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TLLGA
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL
• Development Tools By Supplier: AT32UC3L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 9 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

35.2.9
35.2.10
35.2.11
32099F–11/2010
TWI
PWMA
CAT
5. SPI mode fault detection enable causes incorrect behavior
1. TWIM.SR.IDLE goes high immediately when NAK is received
2. TWIM SMBAL polarity is wrong
1. BUSY bit is never cleared after writes to the Control Register (CR)
2. Incoming peripheral events are discarded during duty cycle register update
1. CAT asynchronous wake will be delayed by one AST peripheral event period
reset the SR.TDRE bit by writing to TDR. So if the SPI is disabled during a PDCA transfer,
the PDCA will continue to write data to TDR (as SR.TDRE stays high) until its buffer is
empty, and all data written after the disable command is lost.
Fix/Workaround
Disable the PDCA, add 2 NOP (minimum), and disable the SPI. To continue the transfer,
enable the SPI and the PDCA.
When mode fault detection is enabled (MR.MODFDIS==0), the SPI module may not operate
properly.
Fix/Workaround
Always disable mode fault detection before using the SPI by writing a one to MR.MODFDIS.
When a NAK is received and there is a non-zero number of bytes to be transmitted,
SR.IDLE goes high immediately and does not wait for the STOP condition to be sent. This
does not cause any problem just by itself, but can cause a problem if software waits for
SR.IDLE to go high and then immediately disables the TWIM by writing a one to CR.MDIS.
Disabling the TWIM causes the TWCK and TWD pins to go high immediately, so the STOP
condition will not be transmitted correctly.
Fix/Workaround
If possible, do not disable the TWIM. If it is absolutely necessary to disable the TWIM, there
must be a software delay of at least two TWCK periods between the detection of
SR.IDLE==1 and the disabling of the TWIM.
The SMBAL signal in the TWIM is active high instead of active low.
Fix/Workaround
Use an external inverter to invert the signal going into the TWIM. When using both TWIM
and TWIS on the same pins, the SMBAL cannot be used.
When writing a non-zero value to CR.TOP, CR.SPREAD, or CR.TCLR when the PWMA is
disabled (CR.EN==0), the BUSY bit in the Status Register (SR.BUSY) will be set, but never
cleared.
Fix/Workaround
When writing a non-zero value to CR.TOP, CR.SPREAD, or CR.TCLR, make sure the
PWMA is enabled, or simultaneously enable the PWMA by writing a one to CR.EN.
Incoming peripheral events to all applied channels will be discarded if a duty cycle update is
received from the user interface in the same PWMA clock period.
Fix/Workaround
Ensure that duty cycle writes from the user interface are not performed in a PWMA clock
period when an incoming peripheral event is expected.
AT32UC3L016/32/64
828