r5f21346mnfp Renesas Electronics Corporation., r5f21346mnfp Datasheet - Page 511

no-image

r5f21346mnfp

Manufacturer Part Number
r5f21346mnfp
Description
Single-chip Mcus Incorporates The R8c Cpu Core
Manufacturer
Renesas Electronics Corporation.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
r5f21346mnfp#V0
Manufacturer:
Renesas Electronics America
Quantity:
10 000
R8C/34M Group
R01UH0131EJ0100 Rev.1.00
Jun 21, 2011
Table 23.10
Note:
U2TB
U2RB
U2BRG
U2MR
U2C0
U2C1
U2SMR
U2SMR2 IICM2
Register
1. Set the bits not listed in this table to 0 when writing to the above registers in I
(1)
(1)
(1)
b0 to b7
b0 to b7
b8
OER
b0 to b7
SMD2 to SMD0 Set to 010b.
CKDIR
IOPOL
CLK1, CLK0
CRS
TXEPT
CRD
NCH
CKPOL
UFORM
TE
TI
RE
RI
U2IRS
U2RRM,
U2LCH, U2ERE
IICM
BBS
b3 to b7
CSC
SWC
STAC
SWC2
SDHI
b7
Registers Used and Settings in I
Bit
Set transmit data.
Receive data can be read.
ACK or NACK is set in this bit.
Overrun error flag
Set a bit rate.
Set to 0.
Set to 0.
Select the count source for the U2BRG
register.
Disabled because CRD = 1.
Transmit register empty flag
Set to 1.
Set to 1.
Set to 0.
Set to 1.
Set to 1 to enable transmission.
Transmit buffer empty flag
Set to 1 to enable reception.
Receive complete flag
Set to 1.
Set to 0.
Set to 1.
Bus busy flag
Set to 0.
Refer to Table 23.12 I
Functions .
Set to 1 to enable clock synchronization.
Set to 1 to fix SCL2 output low at the falling
edge of the 9th bit of clock.
Set to 0.
Set to 1 to forcibly pull SCL2 low.
Set to 1 to disable SDA2 output.
Set to 0.
Master
2
C Mode
2
C Mode (1)
Function
Set transmit data.
Receive data can be read.
ACK or NACK is set in this bit.
Overrun error flag
Disabled
Set to 010b.
Set to 1.
Set to 0.
Disabled
Disabled because CRD = 1.
Transmit register empty flag
Set to 1.
Set to 1.
Set to 0.
Set to 1.
Set to 1 to enable transmission.
Transmit buffer empty flag
Set to 1 to enable reception.
Receive complete flag
Set to 1.
Set to 0.
Set to 1.
Bus busy flag
Set to 0.
Refer to Table 23.12 I
Functions .
Set to 0.
Set to 1 to fix SCL2 output low at the falling
edge of the 9th bit of clock.
Set to 1 to initialize UART2 at start
condition detection
Set to 1 to forcibly pull SCL2 output low.
Set to 1 to disable SDA2 output.
Set to 0.
2
C mode.
23. Serial Interface (UART2)
Slave
2
C Mode
Page 479 of 740

Related parts for r5f21346mnfp