SAM4S16C Atmel Corporation, SAM4S16C Datasheet - Page 480
SAM4S16C
Manufacturer Part Number
SAM4S16C
Description
Manufacturer
Atmel Corporation
Specifications of SAM4S16C
Flash (kbytes)
1024 Kbytes
Pin Count
100
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
79
Ext Interrupts
79
Usb Transceiver
1
Quadrature Decoder Channels
2
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
128
Self Program Memory
YES
External Bus Interface
1
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
- Current page: 480 of 1166
- Download datasheet (28Mb)
26.1.5.4
26.1.5.5
480
480
SAM4S
SAM4S
Main Clock Oscillator Selection
Main Clock Frequency Counter
When enabling the main oscillator, the user must initiate the main oscillator counter with a value
corresponding to the startup time of the oscillator. This startup time depends on the crystal fre-
quency connected to the oscillator.
When the MOSCXTEN bit and the MOSCXTCNT are written in CKGR_MOR to enable the main
oscillator, the XIN and XOUT pins are automatically switched into oscillator mode and
MOSCXTS bit in the Power Management Controller Status Register (PMC_SR) is cleared and
the counter starts counting down on the slow clock divided by 8 from the MOSCXTCNT value.
Since the MOSCXTCNT value is coded with 8 bits, the maximum startup time is about 62 ms.
When the counter reaches 0, the MOSCXTS bit is set, indicating that the main clock is valid.
Setting the MOSCXTS bit in PMC_IMR can trigger an interrupt to the processor.
The user can select either the 4/8/12 MHz Fast RC oscillator or the 3 to 20 MHz Crystal or
Ceramic Resonator-based oscillator to be the source of Main Clock.
The advantage of the 4/8/12 MHz Fast RC oscillator is that it provides fast startup time, this is
why it is selected by default (to start up the system) and when entering Wait Mode.
The advantage of the 3 to 20 MHz Crystal or Ceramic Resonator-based oscillator is that it is very
accurate.
The selection is made by writing the MOSCSEL bit in the Main Oscillator Register
(CKGR_MOR). The switch of the Main Clock source is glitch free, so there is no need to run out
of SLCK, PLLACK or PLLBCK in order to change the selection. The MOSCSELS bit of the
Power Management Controller Status Register (PMC_SR) allows knowing when the switch
sequence is done.
Setting the MOSCSELS bit in PMC_IMR can trigger an interrupt to the processor.
The device features a Main Clock frequency counter that provides the frequency of the Main
Clock.
The Main Clock frequency counter is reset and starts incrementing at the Main Clock speed after
the next rising edge of the Slow Clock in the following cases:
Then, at the 16th falling edge of Slow Clock, the MAINFRDY bit in the Clock Generator Main
Clock Frequency Register (CKGR_MCFR) is set and the counter stops counting. Its value can
be read in the MAINF field of CKGR_MCFR and gives the number of Main Clock cycles during
16 periods of Slow Clock, so that the frequency of the 4/8/12 MHz Fast RC oscillator or 3 to 20
MHz Crystal or Ceramic Resonator-based oscillator can be determined.
• when the 4/8/12 MHz Fast RC oscillator clock is selected as the source of Main Clock and
• when the 3 to 20 MHz Crystal or Ceramic Resonator-based oscillator is selected as the
• when the Main Clock Oscillator selection is modified
• when the RCMEAS bit of CKGR_MFCR is written to 1.
when this oscillator becomes stable (i.e., when the MOSCRCS bit is set)
source of Main Clock and when this oscillator becomes stable (i.e., when the MOSCXTS bit
is set)
11100A–ATARM–28-Oct-11
11100A–ATARM–28-Oct-11
Related parts for SAM4S16C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: