SAM4S16C Atmel Corporation, SAM4S16C Datasheet - Page 397

no-image

SAM4S16C

Manufacturer Part Number
SAM4S16C
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of SAM4S16C

Flash (kbytes)
1024 Kbytes
Pin Count
100
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
79
Ext Interrupts
79
Usb Transceiver
1
Quadrature Decoder Channels
2
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
128
Self Program Memory
YES
External Bus Interface
1
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
22.5.3
22.5.3.1
11100A–ATARM–28-Oct-11
11100A–ATARM–28-Oct-11
USB Device Port
Enumeration Process
The device uses the USB communication device class (CDC) drivers to take advantage of the
installed PC RS-232 software to talk over the USB. The CDC class is implemented in all
releases of Windows
www.usb.org, describes a way to implement devices such as ISDN modems and virtual COM
ports.
The Vendor ID (VID) is Atmel’s vendor ID 0x03EB. The product ID (PID) is 0x6124. These refer-
ences are used by the host operating system to mount the correct driver. On Windows systems,
the INF files contain the correspondence between vendor ID and product ID.
For More details about VID/PID for End Product/Systems, please refer to the Vendor ID form
available from the USB Implementers Forum:
http://www.usb.org/developers/vendor/VID_Only_Form_withCCAuth_102407b.pdf
"Unauthorized use of assigned or unassigned USB Vendor ID Numbers and associated Product
ID Numbers is strictly prohibited."
Atmel provides an INF example to see the device as a new serial port and also provides another
custom driver used by the SAM-BA application: atm6124.sys. Refer to the document “USB Basic
Application”,
The USB protocol is a master/slave protocol. This is the host that starts the enumeration send-
ing requests to the device through the control endpoint. The device handles standard requests
as defined in the USB Specification.
Table 22-3.
The device also handles some class requests defined in the CDC class.
Table 22-4.
Unhandled requests are STALLed.
Request
GET_DESCRIPTOR
SET_ADDRESS
SET_CONFIGURATION
GET_CONFIGURATION
GET_STATUS
SET_FEATURE
CLEAR_FEATURE
Request
SET_LINE_CODING
GET_LINE_CODING
SET_CONTROL_LINE_STATE
literature number
Handled Standard Requests
Handled Class Requests
®
, from Windows 98SE to Windows XP. The CDC document, available at
6123, for more details.
Definition
Returns the current device configuration value.
Sets the device address for all future device access.
Sets the device configuration.
Returns the current device configuration value.
Returns status for the specified recipient.
Set or Enable a specific feature.
Clear or Disable a specific feature.
Definition
Configures DTE rate, stop bits, parity and number of
character bits.
Requests current DTE rate, stop bits, parity and number
of character bits.
RS-232 signal used to tell the DCE device the DTE
device is now present.
SAM4S
SAM4S
397
397

Related parts for SAM4S16C