SAM4S16C Atmel Corporation, SAM4S16C Datasheet - Page 671

no-image

SAM4S16C

Manufacturer Part Number
SAM4S16C
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of SAM4S16C

Flash (kbytes)
1024 Kbytes
Pin Count
100
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
79
Ext Interrupts
79
Usb Transceiver
1
Quadrature Decoder Channels
2
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
128
Self Program Memory
YES
External Bus Interface
1
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
31.6
31.6.1
31.6.2
11100A–ATARM–28-Oct-11
11100A–ATARM–28-Oct-11
Product Dependencies
I/O Lines
Power Management
The pins used for interfacing the USART may be multiplexed with the PIO lines. The program-
mer must first program the PIO controller to assign the desired USART pins to their peripheral
function. If I/O lines of the USART are not used by the application, they can be used for other
purposes by the PIO Controller.
To prevent the TXD line from falling when the USART is disabled, the use of an internal pull up
is mandatory. If the hardware handshaking feature or Modem mode is used, the internal pull up
on TXD must also be enabled.
All the pins of the modems may or may not be implemented on the USART. Only
equipped with all the modem signals. On USARTs not equipped with the corresponding pin, the
associated control bits and statuses have no effect on the behavior of the USART.
Table 31-3.
The USART is not continuously clocked. The programmer must first enable the USART Clock in
the Power Management Controller (PMC) before using the USART. However, if the application
does not require USART operations, the USART clock can be stopped when not needed and be
restarted later. In this case, the USART will resume its operations where it left off.
Configuring the USART does not require the USART clock to be enabled.
Instance
USART0
USART0
USART0
USART0
USART0
USART1
USART1
USART1
USART1
USART1
USART1
USART1
USART1
USART1
I/O Lines
Signal
DCD1
RXD0
SCK0
DSR1
DTR1
RXD1
SCK1
CTS0
RTS0
TXD0
CTS1
RTS1
TXD1
RI1
I/O Line
PA25
PA26
PA28
PA27
PA29
PA24
PA21
PA23
PA22
PA8
PA7
PA5
PA2
PA6
Peripheral
A
A
A
B
A
A
A
A
A
A
A
A
A
A
SAM4S
SAM4S
USART1
fully
671
671

Related parts for SAM4S16C