SAM4S16C Atmel Corporation, SAM4S16C Datasheet - Page 892

no-image

SAM4S16C

Manufacturer Part Number
SAM4S16C
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of SAM4S16C

Flash (kbytes)
1024 Kbytes
Pin Count
100
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
79
Ext Interrupts
79
Usb Transceiver
1
Quadrature Decoder Channels
2
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
128
Self Program Memory
YES
External Bus Interface
1
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
35.14.16 HSMCI Configuration Register
Name:
Address:
Access:
This register can only be written if the WPEN bit is cleared in
• FIFOMODE: HSMCI Internal FIFO control mode
0 = A write transfer starts when a sufficient amount of data is written into the FIFO.
When the block length is greater than or equal to 3/4 of the HSMCI internal FIFO size, then the write transfer starts as soon
as half the FIFO is filled. When the block length is greater than or equal to half the internal FIFO size, then the write transfer
starts as soon as one quarter of the FIFO is filled. In other cases, the transfer starts as soon as the total amount of data is
written in the internal FIFO.
1 = A write transfer starts as soon as one data is written into the FIFO.
• FERRCTRL: Flow Error flag reset control mode
0= When an underflow/overflow condition flag is set, a new Write/Read command is needed to reset the flag.
1= When an underflow/overflow condition flag is set, a read status resets the flag.
• HSMODE: High Speed Mode
0= Default bus timing mode.
1= If set to one, the host controller outputs command line and data lines on the rising edge of the card clock. The Host
driver shall check the high speed support in the card registers.
• LSYNC: Synchronize on the last block
0= The pending command is sent at the end of the current data block.
1= The pending command is sent at the end of the block transfer when the transfer length is not infinite. (block count shall
be different from zero)
892
892
31
23
15
7
SAM4S
SAM4S
30
22
14
HSMCI_CFG
0x40000054
Read-write
6
29
21
13
5
FERRCTRL
LSYNC
28
20
12
4
“HSMCI Write Protect Mode Register” on page
27
19
11
3
26
18
10
2
25
17
9
1
11100A–ATARM–28-Oct-11
11100A–ATARM–28-Oct-11
893.
FIFOMODE
HSMODE
24
16
8
0

Related parts for SAM4S16C