SAM4S16C Atmel Corporation, SAM4S16C Datasheet - Page 899

no-image

SAM4S16C

Manufacturer Part Number
SAM4S16C
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of SAM4S16C

Flash (kbytes)
1024 Kbytes
Pin Count
100
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
79
Ext Interrupts
79
Usb Transceiver
1
Quadrature Decoder Channels
2
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
128
Self Program Memory
YES
External Bus Interface
1
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
36.5.2
36.5.3
36.5.4
Table 36-4.
Note:
11100A–ATARM–28-Oct-11
11100A–ATARM–28-Oct-11
Fault Inputs
PA9
Main OSC
ADC
Analog Comparator
Timer0
Timer1
1. FPOL bit in PWMC_FMR.
Power Management
Interrupt Sources
Fault Inputs
Fault Inputs
Table 36-2.
The PWM is not continuously clocked. The programmer must first enable the
Power Management Controller (PMC) before using the
not require PWM operations, the
later. In this case, the
In the
is connected.
The
Using the
not recommended to use the
Table 36-3.
The
mentation of these module within the product for detailed information about the fault generation
procedure. The
Controller and Timer/Counters
External PWM Fault Input Number
PWMFI0
PWM
PWM
Instance
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
interrupt line is connected on one of the internal sources of the Interrupt Controller.
PWM
has the FAULT inputs connected to the different modules. Please refer to the imple-
description, Master Clock (MCK) is the clock of the peripheral bus to which the
I/O Lines
Peripheral IDs
PWM
interrupt requires the Interrupt Controller to be programmed first. Note that it is
receives faults from PIO inputs, PMC, ADC controller, Analog Comparator
PWM
31
ID
will resume its operations where it left off.
PWM
PWM
interrupt line in edge sensitive mode.
PWML1
PWML2
PWML2
PWML2
PWML2
PWML3
PWML3
PWML3
clock can be stopped when not needed and be restarted
Polarity Level
User Defined
1
1
1
1
1
(1)
PWM
. However, if the application does
PC15
PC22
PB13
PA16
PA30
PA15
PC2
PC3
Fault Input ID
0
1
2
3
4
5
PWM
SAM4S
SAM4S
clock in the
C
C
B
A
A
B
B
B
PWM
899
899

Related parts for SAM4S16C