SAM4S16C Atmel Corporation, SAM4S16C Datasheet - Page 270

no-image

SAM4S16C

Manufacturer Part Number
SAM4S16C
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of SAM4S16C

Flash (kbytes)
1024 Kbytes
Pin Count
100
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
79
Ext Interrupts
79
Usb Transceiver
1
Quadrature Decoder Channels
2
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
128
Self Program Memory
YES
External Bus Interface
1
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
13.4.4.2
13.4.4.3
Figure 13-4. User Reset State
270
270
periph_nreset
proc_nreset
(nrst_out)
RSTTYP
SAM4S
SAM4S
NRST
SLCK
NRST
MCK
Backup Reset
User Reset
A Backup reset occurs when the chip returns from Backup mode. The core_backup_reset signal
is asserted by the Supply Controller when a Backup reset occurs.
The field RSTTYP in RSTC_SR is updated to report a Backup Reset.
The User Reset is entered when a low level is detected on the NRST pin and the bit URSTEN in
RSTC_MR is at 1. The NRST input signal is resynchronized with SLCK to insure proper behav-
ior of the system.
The User Reset is entered as soon as a low level is detected on NRST. The Processor Reset
and the Peripheral Reset are asserted.
The User Reset is left when NRST rises, after a two-cycle resynchronization time and a 3-cycle
processor startup. The processor clock is re-enabled as soon as NRST is confirmed high.
When the processor reset signal is released, the RSTTYP field of the Status Register
(RSTC_SR) is loaded with the value 0x4, indicating a User Reset.
T h e
EXTERNAL_RESET_LENGTH Slow Clock cycles, as programmed in the field ERSTL. How-
ever, if NRST does not rise after EXTERNAL_RESET_LENGTH because it is driven low
externally, the internal reset lines remain asserted until NRST actually rises.
Resynch.
2 cycles
Any
Freq.
Any
N R S T
>= EXTERNAL RESET LENGTH
M a n a g e r
g u a r a n t e e s
Resynch.
2 cycles
XXX
t h a t
Processor Startup
t h e
= 2 cycles
N R S T
l i n e
0x4 = User Reset
i s
11100A–ATARM–28-Oct-11
11100A–ATARM–28-Oct-11
a s s e r t e d
f o r

Related parts for SAM4S16C