SAM4S16C Atmel Corporation, SAM4S16C Datasheet - Page 882

no-image

SAM4S16C

Manufacturer Part Number
SAM4S16C
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of SAM4S16C

Flash (kbytes)
1024 Kbytes
Pin Count
100
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
79
Ext Interrupts
79
Usb Transceiver
1
Quadrature Decoder Channels
2
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
128
Self Program Memory
YES
External Bus Interface
1
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
35.14.12 HSMCI Status Register
Name:
Address:
Access:
• CMDRDY: Command Ready
0 = A command is in progress.
1 = The last command has been sent. Cleared when writing in the HSMCI_CMDR.
• RXRDY: Receiver Ready
0 = Data has not yet been received since the last read of HSMCI_RDR.
1 = Data has been received since the last read of HSMCI_RDR.
• TXRDY: Transmit Ready
0= The last data written in HSMCI_TDR has not yet been transferred in the Shift Register.
1= The last data written in HSMCI_TDR has been transferred in the Shift Register.
• BLKE: Data Block Ended
This flag must be used only for Write Operations.
0 = A data block transfer is not yet finished. Cleared when reading the HSMCI_SR.
1 = A data block transfer has ended, including the CRC16 Status transmission.
the flag is set for each transmitted CRC Status.
Refer to the MMC or SD Specification for more details concerning the CRC Status.
• DTIP: Data Transfer in Progress
0 = No data transfer in progress.
1 = The current data transfer is still in progress, including CRC16 calculation. Cleared at the end of the CRC16 calculation.
• NOTBUSY: HSMCI Not Busy
This flag must be used only for Write Operations.
A block write operation uses a simple busy signalling of the write operation duration on the data (DAT0) line: during a data
transfer block, if the card does not have a free data receive buffer, the card indicates this condition by pulling down the data
line (DAT0) to LOW. The card stops pulling down the data line as soon as at least one receive buffer for the defined data
transfer block length becomes free.
The NOTBUSY flag allows to deal with these different states.
882
882
TXBUFE
CSTOE
ENDTX
UNRE
31
23
15
7
SAM4S
SAM4S
RXBUFF
ENDRX
OVRE
DTOE
30
22
14
HSMCI_SR
0x40000040
Read-only
6
ACKRCVE
NOTBUSY
DCRCE
CSRCV
29
21
13
5
SDIOWAIT
ACKRCV
RTOE
DTIP
28
20
12
4
XFRDONE
RENDE
BLKE
27
19
11
3
FIFOEMPTY
RCRCE
TXRDY
26
18
10
2
RXRDY
RDIRE
25
17
9
1
11100A–ATARM–28-Oct-11
11100A–ATARM–28-Oct-11
SDIOIRQA
CMDRDY
RINDE
24
16
8
0

Related parts for SAM4S16C