SAM4S16C Atmel Corporation, SAM4S16C Datasheet - Page 993

no-image

SAM4S16C

Manufacturer Part Number
SAM4S16C
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of SAM4S16C

Flash (kbytes)
1024 Kbytes
Pin Count
100
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
79
Ext Interrupts
79
Usb Transceiver
1
Quadrature Decoder Channels
2
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
128
Self Program Memory
YES
External Bus Interface
1
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
37.7.2
Name:
Address:
Access:
This register is used to get and set the device state as specified in Chapter 9 of the USB Serial Bus Specification, Rev.2.0.
• FADDEN: Function Address Enable
Read:
0 = Device is not in address state.
1 = Device is in address state.
Write:
0 = No effect, only a reset can bring back a device to the default state.
1 = Sets device in address state. This occurs after a successful Set Address request. Beforehand, the UDP_FADDR regis-
ter must have been initialized with Set Address parameters. Set Address must complete the Status Stage before setting
FADDEN. Refer to chapter 9 of the Universal Serial Bus Specification, Rev. 2.0 for more details.
• CONFG: Configured
Read:
0 = Device is not in configured state.
1 = Device is in configured state.
Write:
0 = Sets device in a non configured state
1 = Sets device in configured state.
The device is set in configured state when it is in address state and receives a successful Set Configuration request. Refer
to Chapter 9 of the Universal Serial Bus Specification, Rev. 2.0 for more details.
• ESR: Enable Send Resume
0 = Mandatory value prior to starting any Remote Wake Up procedure.
1 = Starts the Remote Wake Up procedure if this bit value was 0 and if RMWUPE is enabled.
• RMWUPE: Remote Wake Up Enable
0 = The Remote Wake Up feature of the device is disabled.
1 = The Remote Wake Up feature of the device is enabled.
11100A–ATARM–28-Oct-11
11100A–ATARM–28-Oct-11
31
23
15
7
UDP Global State Register
30
22
14
UDP_GLB_STAT
0x40034004
Read-write
6
29
21
13
5
RMWUPE
28
20
12
4
RSMINPR
27
19
11
3
ESR
26
18
10
2
CONFG
25
17
9
1
SAM4S
SAM4S
FADDEN
24
16
8
0
993
993

Related parts for SAM4S16C