TMPM382FSFG Toshiba, TMPM382FSFG Datasheet - Page 25

no-image

TMPM382FSFG

Manufacturer Part Number
TMPM382FSFG
Description
Manufacturer
Toshiba
Datasheet

Specifications of TMPM382FSFG

Product Summaries
Summary
Lead Free
Yes
Rohs Compatible Product(s)
Available
Rom (kbytes)
64K
Rom Type
Flash
Ram (kbytes)
8K
Number Of Pins
64
Package
QFP(14x14)
Vcc
5V
Cpu Mhz
40
Ssp (ch) Spi
1
I2c/sio (ch)
1
Uart/sio (ch)
3
Usb
-
Can
-
Ethernet
-
External Bus Interface
N
Cs/wait Controller (ch)
-
Dma Controller
2
10-bit Da Converter
-
10-bit Ad Converter
-
12-bit Ad Converter
10
16-bit Timer / Counter
6
Motor / Igbt Control
Y
Real Time Clock
1
Watchdog Timer
Y
Osc Freq Detect
Y
Clock Gear
Y
Low-power Hold Function
-
Remote Control Interface
Y
Hardware Cec Controller
-
Comparators
-
Low-voltage Detector
Y
Etm Hardware Trace
2-bit
4
4.1
4.2
4.3
4.4
Dubug Interface
TMS/SWDIO
TCK/SWCLK
TDO/SWV
TDI
TRST
TRACECLK
TRACEDATA0
TRACEDATA1
---------------
Table 4-1 SWJ-DP、ETM function
(Note) In case of enabling SWV function.
Specification Overview
Features of SWJ-DP
Features of ETM
Pin Functions
the In-Circuit Emulator (ICE) and the Embedded Trace Macrocell
output. Trace data is output to the dedicated pins (TRACEDATA[0]-[1], SWV) via the on-chip Trace
Port Interface Unit (TPIU).
Port (TDI, TDO, TMS, TCK, TRST).
trace output from SWV.
between the JTAG debug port function and the serial wire debug port function. The PB5 is shared
between the JTAG debug port function and the SWV trace output function.
functions of other debug interface pins need to be programmed as required. Debug interface pins
can use general purpose port that is not use debug interface.
Pin name
SWJ-DP
The TMPM380/M382 contains the Serial Wire JTAG Debug Port (SWJ-DP) unit for interfacing with
For details about SWJ-DP, ETM and TPIU, refer to “Cortex-M3 Technical Reference Manual”.
SWJ-DP supports the two-pin Serial Wire Debug Port (SWDCK, SWDIO) and the JTAG Debug
The debug interface pins can also be used as general-purpose ports. The PB3 and PB4 are shared
After reset, the PB3, PB4, PB5, PB6 and PB7 are configured as debug port function pins. The
ETM supports two data signal pins (TRACEDATA[0]-[1]), one clock signal pin (TRACECLK) and
Name of
port
PB3
PB4
PB5
PB6
PB7
PB0
PB1
PB2
Output
Output
Output
Output
Input
Input
Input
Input
I/O
TMPM380/M382 - 1 / 3 -
JTAG debug function
JTAG Test Data Output
JTAG Test Data Input
JTAG Test RESET
JTAG Test Check
JTAG Test Mode
Discription
Selection
-------------------
TRACE DATA Output0
TRACE DATA Output1
TRACE Clock Output
TM
(ETM) unit for instruction trace
(Output)
Input
(Note)
I/O
I/O
SW debug
TMPM380/M382
Serial Wire Clock
Serial Wire Data
Viewer Output)
Input/Output
Discription
(Serial Wire

Related parts for TMPM382FSFG