TMPM382FSFG Toshiba, TMPM382FSFG Datasheet - Page 292

• Manufacturer Part Number: TMPM382FSFG
• Manufacturer: Toshiba

Specifications of TMPM382FSFG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 64K
• Rom Type: Flash
• Ram (kbytes): 8K
• Number Of Pins: 64
• Package: QFP(14x14)
• Vcc: 5V
• Cpu Mhz: 40
• Ssp (ch) Spi: 1
• I2c/sio (ch): 1
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: N
• Cs/wait Controller (ch): -
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: -
• 12-bit Ad Converter: 10
• 16-bit Timer / Counter: 6
• Motor / Igbt Control: Y
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: Y
• Hardware Cec Controller: -
• Comparators: -
• Low-voltage Detector: Y
• Etm Hardware Trace: 2-bit

how AD conversion is started.
factor (PMD, Timer, Software, Constant), <ADBFN> is set to “1”. When finished AD conversion, <ADBFN> is
cleared to “0”.
actually started, <ADSFN> is set to “1”. When finished AD conversion, <ADSFN> is cleared to “0”.
0x4003_000C
0x4003_0004
0x4003_0008
ADMOD0
Setting <DACON> to “1”, when using the ADC.
Setting <ADSS> to “1” starts AD conversion (software triggered conversion). Receiving trigger signal from
PMD(MPT) or TMRB(interrupt) starts AD conversion also.
ADMOD1
Setting <ADEN> to “1”, when using the ADC. After Setting <ADEN> to “1”, setting <ADAS> to “1” starts AD
conversion and repeat conversion.
ADMOD2
The <ADBFN> is an AD conversion busy flag. When AD conversion is started regardless of conversion
The <ADSFN> is a software AD conversion busy flag. After <ADSS> was set to “1”, when AD conversion is
The ADC Mode Setting Registers (ADMOD0, ADMOD1, ADMOD2 and ADMOD3) are used to select
For detail setting, please read the chapter about PMD(MPT) and TMRB.
11.3.2 Mode Setting Registers
11.3.2.1
11.3.2.2
11.3.2.3
Read/Write
Read/Write
Read/Write
Bit symbol
After reset
Bit symbol
After reset
Bit symbol
After reset
Function
Function
Function
ADMOD0
ADMOD1
ADMOD2
AD
conversion
control
0: Disable
1: Enable
ADEN
R/W
7
7
0
7
6
6
6
TMPM380/M382 - 5 / 39 -
Always read as 0.
Always read as 0.
5
5
5
R
R
0
0
-
-
Always read as 0.
4
4
4
R
0
-
3
3
3
2
2
2
DAC control
0: off
1: On
Software
0:
Conversion
completed
1:
Conversion
in progress
conversion
busy flag
TMPM380/M382
DACON
ADSFN
R/W
R
1
0
1
1
0
Software
0 ： Don't care
1: Start
Constant
0: Disable
1: Enable
AD
conversion
busy flag
0:
Conversion
not in
progress
1:
Conversion
in progress
triggered
conversion
AD
conversion
control
ADBFN
ADSS
ADAS
R/W
W
R
0
0
0
0
0
0